What to do if the Toshiba BA410T shows 'COVER OPEN'?
If your Toshiba Barcode Reader displays a 'COVER OPEN' error, it means a feed or issue was attempted with the Front Cover opened. Close the Front Cover, then press the [RESTART] key.
What to do if my Toshiba BA410T has a paper jam?
If your Toshiba Barcode Reader is experiencing a paper jam, there are several potential causes and solutions: 1. If the media is jammed, remove the jammed media, clean the Platen, reload the media correctly, and then press the [RESTART] key. 2. If a wrong Media Sensor is selected, turn the printer off and then on, select the correct Media Sensor, and resend the print job. 3. If the Black Mark Sensor is misaligned, adjust the sensor position and press the [RESTART] key. 4. If the media size is incorrect, replace it with the correct size and press the [RESTART] key, or turn the printer off and on, select a matching programmed size, and resend the job. 5. If the Upper and Lower Sensors misalign, align them. 6. If using media with Black mark and Gap, and 'CALIBRATE' is set to 'ON ALL' o...
What to do when Toshiba BA410T Barcode Reader shows 'LOW BATTERY'?
When your Toshiba Barcode Reader displays 'LOW BATTERY', it means the voltage of the Real Time Clock Battery is 1.9V or less. Hold down the [RESTART] key until “RESET” is displayed. To continue using the same battery, set the Low battery check function to OFF and set the date and time. Note that the date and time will reset when the power is turned off.
What to do if my Toshiba BA410T shows 'RFID ERROR'?
If your Toshiba Barcode Reader displays an 'RFID ERROR', it means the printer cannot communicate with the RFID module. Turn the printer off, and then on again.
What does 'RFID WRITE ERROR' mean on my Toshiba Barcode Reader?
The 'RFID WRITE ERROR' message on your Toshiba Barcode Reader indicates that the printer failed to write data onto an RFID tag after multiple retries. Press the [RESTART] key.
What to do if Toshiba BA410T Barcode Reader says 'MEMORY FULL'?
The 'MEMORY FULL' message on your Toshiba Barcode Reader means saving failed due to insufficient flash ROM capacity. Turn the printer off, and then on again.
How to fix 'FORMAT ERROR' on Toshiba BA410T Barcode Reader?
The 'FORMAT ERROR' message on your Toshiba Barcode Reader indicates an error occurred while formatting the flash ROM. Turn the printer off, and then on again.
What does 'EXCESS HEAD TEMP' mean on Toshiba Barcode Reader?
The 'EXCESS HEAD TEMP' error on your Toshiba Barcode Reader indicates that the Print Head has overheated. Turn off the printer and allow it to cool down for about 3 minutes.
What does 'SYSTEM ERROR' mean on my Toshiba BA410T Barcode Reader?
A 'SYSTEM ERROR' on your Toshiba Barcode Reader can be caused by several factors: * The printer is used in a noisy location, or near power cords of other electrical appliances. Keep the printer and interface cables away from noise sources. * The printer's power cord is not grounded. Ground the power cord. * The printer shares a power source with other electrical appliances. Provide an exclusive power source for the printer. * The application software on your host computer has an error. Confirm the host computer operates properly.
What causes a 'RIBBON ERROR' on a Toshiba BA410T Barcode Reader?
A 'RIBBON ERROR' on your Toshiba Barcode Reader can occur for the following reasons: * The ribbon is not fed properly. Remove the ribbon, check its status, and replace it if necessary. * The ribbon has run out. Load a new ribbon and then press the [RESTART] key.
General| Print Technology | Thermal Transfer / Direct Thermal |
|---|---|
| Print Speed | Max 8 ips |
| Print Method | Thermal Transfer / Direct Thermal |
| Print Resolution | 203 dpi |
| Max Print Width | 4.09 inches |
| Connectivity | USB, Ethernet |
| Resolution | 203 dpi |
| Print Width | 4.09 inches |
| Interfaces | USB, Ethernet |
| Media Type | Roll, Fanfold |
| Media Thickness | 0.06 to 0.19 mm |
| Type | Thermal Printer |
| Interface | USB |
| Storage Temperature | -20°C to 60°C |
| Humidity | 25 to 85% non-condensing |
| Media Width | 25.4 – 112 mm (1.0" – 4.4") |
| Ribbon Width | 1.57 to 4.33 inches |
| Operating Temperature | 5 – 40 °C (41 – 104 °F), 25 – 85% RH non-condensing |
Provides a general introduction to the owner's manual and printer.
Highlights key features like space-saving design, various interfaces, superior hardware, and easy maintenance.
Lists accessories supplied with the printer upon unpacking.
Details physical dimensions, front, and rear views of the printer.
Explains the printer's operation panel and interior components.
Describes available optional modules like cutter, strip, and interface boards.
Outlines the steps for installing the printer on a safe and stable location.
Covers connecting the power cord and the printer to a host computer or network.
Provides instructions for loading media (labels/tags) and ribbon for printing.
Details the procedure for turning the printer on and verifying its status.
Explains how to clean the print head, platen, sensors, covers, and panels.
Covers cleaning procedures for optional cutter and strip modules.
Lists common error messages, their causes, and recommended solutions.
Describes typical problems like no print, blurred image, or feed issues with their causes and solutions.
Provides detailed steps for safely removing jammed media from the printer.
Details the specifications and pinouts for USB and LAN standard interfaces.
Describes the specifications for Bluetooth and NFC modules.
Covers the specifications and pinouts for optional serial and parallel interfaces.
Explains specifications for Wireless LAN and RFID modules.
Provides essential cautions and guidelines for using RFID tags with the printer.
To Next Page