How do I resolve 'FLASH WRITE ERR.' on my Toshiba BA410T Barcode Reader?
The 'FLASH WRITE ERR.' message on your Toshiba Barcode Reader indicates an error occurred while writing to the flash ROM. To resolve this, turn the printer off and then on again.
What causes a 'CUTTER ERROR' on my Toshiba BA410T?
A 'CUTTER ERROR' on your Toshiba Barcode Reader (when an optional cutter module is installed) means the media is jammed in the cutter. Remove the jammed media and then press the [RESTART] key.
What should I do if my Toshiba Barcode Reader indicates 'POWER FAILURE'?
A 'POWER FAILURE' message on your Toshiba Barcode Reader indicates a momentary power failure. Check the power source supplying power to the printer. If the rating is incorrect, or if the printer shares the same power outlet with other electrical appliances that consume large amounts of power, change the outlet.
What to do if my Toshiba Barcode Reader shows 'HEAD OPEN' error?
The 'HEAD OPEN' error on your Toshiba Barcode Reader indicates that the Top Cover is opened in Online mode or a feed/issue was attempted with the Top Cover open. To resolve this, close the Top Cover and then press the [RESTART] key.
Why does my Toshiba BA410T Barcode Reader show a 'COMMS ERROR'?
A 'COMMS ERROR' on your Toshiba Barcode Reader indicates a communication error. Ensure the interface cable is correctly connected to both the printer and the host, and verify that the host is turned on.
How to fix 'No Paper' error on Toshiba BA410T Barcode Reader?
If your Toshiba Barcode Reader displays a 'No Paper' error, it could be due to a few reasons: * The media has run out. Load new media and then press the [RESTART] key. * The media is not loaded properly. Reload the media correctly and then press the [RESTART] key. * The media is slack. Take up any slack in the media.
Why does my Toshiba BA410T Barcode Reader display 'SYNTAX ERROR'?
A 'SYNTAX ERROR' on your Toshiba Barcode Reader indicates that, while in Download mode for upgrading the firmware, the printer received an improper command. Turn the printer off, and then on again.
General| Print Technology | Thermal Transfer / Direct Thermal |
|---|---|
| Print Speed | Max 8 ips |
| Print Method | Thermal Transfer / Direct Thermal |
| Print Resolution | 203 dpi |
| Max Print Width | 4.09 inches |
| Connectivity | USB, Ethernet |
| Resolution | 203 dpi |
| Print Width | 4.09 inches |
| Interfaces | USB, Ethernet |
| Media Type | Roll, Fanfold |
| Media Thickness | 0.06 to 0.19 mm |
| Type | Thermal Printer |
| Interface | USB |
| Storage Temperature | -20°C to 60°C |
| Humidity | 25 to 85% non-condensing |
| Media Width | 25.4 – 112 mm (1.0" – 4.4") |
| Ribbon Width | 1.57 to 4.33 inches |
| Operating Temperature | 5 – 40 °C (41 – 104 °F), 25 – 85% RH non-condensing |
Provides a general introduction to the owner's manual and printer.
Highlights key features like space-saving design, various interfaces, superior hardware, and easy maintenance.
Lists accessories supplied with the printer upon unpacking.
Details physical dimensions, front, and rear views of the printer.
Explains the printer's operation panel and interior components.
Describes available optional modules like cutter, strip, and interface boards.
Outlines the steps for installing the printer on a safe and stable location.
Covers connecting the power cord and the printer to a host computer or network.
Provides instructions for loading media (labels/tags) and ribbon for printing.
Details the procedure for turning the printer on and verifying its status.
Explains how to clean the print head, platen, sensors, covers, and panels.
Covers cleaning procedures for optional cutter and strip modules.
Lists common error messages, their causes, and recommended solutions.
Describes typical problems like no print, blurred image, or feed issues with their causes and solutions.
Provides detailed steps for safely removing jammed media from the printer.
Details the specifications and pinouts for USB and LAN standard interfaces.
Describes the specifications for Bluetooth and NFC modules.
Covers the specifications and pinouts for optional serial and parallel interfaces.
Explains specifications for Wireless LAN and RFID modules.
Provides essential cautions and guidelines for using RFID tags with the printer.
To Next Page