Toshiba B-852 - User Manual

Other manuals for Toshiba B-852

User Manual2 pages

Questions and Answers

T
Tara JacksonNov 21, 2025
What to do if my Toshiba Barcode Reader has a paper jam?
- R
  romerorebeccaNov 21, 2025
  If your Toshiba Barcode Reader indicates a paper jam, there could be several reasons: 1. The media is jammed, or not feeding smoothly. Remove the jammed media, clean the platen, reload the media properly, and press the [RESTART] key. 2. A wrong media sensor is selected. Turn the printer off and then on, select the correct media sensor, and resend the print job. 3. The Black Mark Sensor is misaligned. Adjust the sensor position and press the [RESTART] key. 4. The media size is inconsistent with the programmed size. Turn the printer off and on. Either replace the media with the correct size or select a matching programmed size, then resend the print job. 5. The Feed Gap Sensor is not working properly. Refer to Section 2.13 to set the threshold. If the issue persists, turn off the print...
N
nixonashleyAug 25, 2025
What does 'SYNTAX ERROR' mean on my Toshiba Barcode Reader and how can I fix it?
- A
  Angela SmithAug 26, 2025
  If your Toshiba Barcode Reader displays 'SYNTAX ERROR', it means that while in Download mode for upgrading the firmware, it received an improper command. Turn the printer off, and then on again.
C
Christy CruzAug 26, 2025
What to do if my Toshiba B-852 says 'NO PAPER'?
- L
  Lisa GriffinAug 27, 2025
  If your Toshiba Barcode Reader displays a 'NO PAPER' error, it could be due to these reasons: 1. The media has run out. Load new media and then press the [RESTART] key. 2. The media is not loaded properly. Ensure the media is loaded correctly, then press the [RESTART] key. 3. The media is slack. Take up any slack in the media.
B
barnesashleeAug 27, 2025
Why is my Toshiba Barcode Reader not printing anything on the media?
- S
  Sonya WaltonAug 28, 2025
  If your Toshiba Barcode Reader is not printing, it could be due to several reasons: 1. The media is not loaded properly. Ensure the media is correctly loaded. 2. The ribbon is not loaded properly. Make sure the ribbon is loaded correctly. 3. The print head is not installed properly. Install the print head correctly and close the Print Head Block. 4. The ribbon and media are not matched. Select an appropriate ribbon for the media type you are using.
E
erika64Aug 29, 2025
What to do if my Toshiba Barcode Reader shows a 'COMMS ERROR'?
- T
  Tracy HarperAug 29, 2025
  If your Toshiba Barcode Reader is showing a 'COMMS ERROR', it means a communication error has occurred. Ensure that the interface cable is firmly connected to the computer and that the computer is turned on.
S
Steven EricksonSep 23, 2025
What to do if my Toshiba Barcode Reader shows a 'LOW BATTERY' message?
- A
  Angela YuSep 23, 2025
  If your Toshiba Barcode Reader displays a 'LOW BATTERY' message, it means the voltage of the Real Time Clock Battery is low. Hold down the [RESTART] key until “RESET” is displayed. If you want to continue using the same battery, set the Low battery check function to OFF and reset the date and time. Contact a TOSHIBA TEC authorized service representative for battery replacement.
F
Felicia RussellSep 16, 2025
What to do if my Toshiba B-852 displays 'FLASH CARD FULL'?
- T
  Tammy Carroll DDSSep 16, 2025
  If your Toshiba Barcode Reader displays 'FLASH CARD FULL', it means saving failed due to insufficient capacity of the flash ROM. Turn the printer off, and then on again.
A
amanda46Sep 18, 2025
What to do if my Toshiba B-852 shows 'EEPROM ERROR'?
- R
  Rhonda JenkinsSep 18, 2025
  If your Toshiba Barcode Reader displays 'EEPROM ERROR', it means data cannot be properly read from or written to a backup EEPROM. Turn the printer off, and then on again.
C
cheryl64Sep 8, 2025
What to do if my Toshiba B-852 Barcode Reader displays 'HEAD ERROR'?
- T
  Tanya WoodwardSep 8, 2025
  If your Toshiba Barcode Reader shows a 'HEAD ERROR', it indicates a problem with the Print Head. Replace the Print Head, and then press the [RESTART] key.
K
Kimberly FordSep 5, 2025
Why is my Toshiba Barcode Reader not feeding media?
- J
  Jenna HopkinsSep 5, 2025
  If your Toshiba Barcode Reader is not feeding media, it could be because: 1. The media is not loaded properly. Ensure the media is loaded correctly. 2. The printer is in an error condition. Solve the error shown in the Message Display. Adjust the print settings using the printer driver or a print command to match your printing conditions. Then, clear the error by pressing the [RESTART] key.