© 2004 - 2010 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/203L/230/230L/232/233/280/282/283
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 5
2
E910 Finisher jam
(Bridge unit)
Jam at the bridge unit transport sensor-1: The
paper does not reach the bridge unit transport sen-
sor-1 after it has passed the exit sensor.
P. 5 - 3 5
E920 Stop jam at the bridge unit transport sensor-1: The
trailing edge of the paper does not pass the bridge
unit transport sensor-1 after its leading edge has
reached the sensor.
P. 5 - 3 5
E930 Jam at the bridge unit transport sensor-2: The trail-
ing edge of the paper does not reach the bridge unit
transport sensor-2 after its leading edge has
reached the bridge unit transport sensor-1.
P. 5 - 3 5
E940 Stop jam at the bridge unit transport sensor-2: The
trailing edge of the paper does not reach the bridge
unit transport sensor-2 after its leading edge has
reached the bridge unit transport sensor-2.
P. 5 - 3 5
E950 Job separator jam Jam not reaching the job separator transport sen-
sor: The paper has passed through the exit sensor
does not reach the job separator transport sensor.
P. 5 - 11
E951 Stop jam at the job separator transport sensor: The
trailing edge of the paper does not pass the job sep-
arator transport sensor.
P. 5 - 11
E960 Offset tray jam Jam not reaching the offset tray transport sensor:
The paper has passed through the exit sensor does
not reach the offset tray transport sensor.
P. 5 - 11
E961 Stop jam at the offset tray transport sensor: The
trailing edge of the paper does not pass the offset
tray transport sensor.
P. 5 - 11
E9F0 Finisher jam
(Puncher unit)
Punching jam: Punching is not performed properly.
[MJ-1025 (When MJ-6005 is installed)]
P. 5 - 3 6
EA10 Finisher jam
(Finisher unit)
Paper transport delay jam: The paper which has
passed the bridge unit does not reach the inlet sen-
sor. [MJ-1022/1025]
P. 5 - 3 7
EA20 Paper transport stop jam: The paper does not pass
through the inlet sensor. [MJ-1022/1025]
P. 5 - 3 8
EA30 Power-ON jam: Paper exists at the inlet sensor
when power is turned ON. [MJ-1022/1025]
P. 5 - 3 9
EA40 Door open jam: The finisher has been released
from the equipment during printing. [MJ-1022/1025]
P. 5 - 4 0
EA50 Stapling jam: Stapling is not performed properly.
[MJ-1022/1025]
P. 5 - 4 1
EA60 Early arrival jam: The inlet sensor detects the paper
earlier than a specified timing. [MJ-1022]
P. 5 - 4 2
EA70 Stack delivery jam: It cannot deliver the stack of
paper on the intermediary process tray to the stack
tray. [MJ-1022/1025]
P. 5 - 4 3
EAB0 Finisher jam
(Saddle Stitcher sec-
tion)
Saddle paper transport stop jam: The paper which
passed through the inlet sensor does not reach or
pass through the folding position sensor. [MJ-1025]
P. 5 - 4 5
EAC0 Saddle transport delay jam: The paper which has
reached the inlet sensor does not pass through this
sensor. [MJ-1025]
P. 5 - 4 5
EAD0 Other paper jam Print end command time-out jam: The printing has
not finished normally because of the communica-
tion error between the SYS board and LGC board
at the end of printing.
P. 5 - 4 6
Error code Classification Contents Troubleshooting
To Next Page
Loading...
