Trane S9V2B060U3VSAD User Manual

SSAAFFEETTYY WWAARRNNIINNGG
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning
equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person
could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that
are attached to the equipment.
December 2022
SS99VV22--VVSS--SSVVXX000011--11BB--EENN
Upflow/Horizontal and Dedicated Downflow
Gas-Fired, Direct/Non-Direct Vent, 2-Stage
Condensing Variable Speed Furnaces with Variable Speed
Draft Inducer
UUppffllooww,, CCoonnvveerrttiibbllee ttoo
HHoorriizzoonnttaall RRiigghhtt oorr
HHoorriizzoonnttaall LLeefftt
S9V2B040U3VSAE
S9V2B060U3VSAC/D
S9V2B080U4VSAC/D
S9V2C100U4VSAC/D
S9V2D120U5VSAC/D
DDoowwnnffllooww OOnnllyy
S9V2B080D4VSAC/D
S9V2C100D4VSAC/D
NNoottee:: Graphics in this document are for representation
only. Actual model may differ in appearance.
CAUTION
!
Failure to follow this Caution could result in property damage or personal injury. 4GXC* and
4MXC* coils installed on upflow furnaces in vertical, horizontal left, or horizontal right
orientations without a factory installed metal drain pan shield must use a MAY*FERCOLKITAA
kit. Coils installed on upflow furnaces must have drain pans that are suitable for 400° F
(205°C) or have a metal drain pan shield. Downflow furnaces do not require a metal drain pan
shield or the use of the MAY*FERCOLKITAA kit.
COIL REQUIREMENT!
S9V2-VS-SVX001-1B-EN
Installation, Operation, and Maintenance

Trane S9V2B060U3VSAD Specifications

General

Model	S9V2B060U3VSAD
Type	Gas Furnace
Efficiency Rating	High Efficiency
Heating Capacity	60, 000 BTU/h
Input BTU/h	60, 000 BTU/h
Ignition Type	Hot Surface Ignition
Maximum External Static Pressure	0.8 in. W.C.
Brand	Trane
Category	Furnace
Stages	2-Stage
Blower Type	Variable Speed
Motor Type	ECM Motor
Warranty	10 Years Limited
Gas Type	Natural Gas
Voltage	120V

Summary

Installation, Operation, and Maintenance

Product Overview and Coil Requirements

Describes furnace types and specific coil installation requirements.

Safety Section — Furnaces

General Safety Warnings

Covers fire, explosion, electrical shock, and carbon monoxide hazards.

Furnace Installation Guidelines

Safety Practices and Precautions

Essential safety practices for installation, servicing, and operation.

Locations and Clearances

Furnace General Installation

Gas Piping and Combustion Checks

Instructions for gas piping connection and combustion/input rate checks.

Gas Valve Adjustment and High Altitude Derate

Venting Requirements and Terminations

Vent Lengths and Horizontal Venting

Clearances and Through-Wall Venting

Venting Through Roof and Chimneys

Downward Venting and Air Supply

General Start-up and Adjustment

Preliminary Inspections and Lighting

Pre-operation checks, startup sequence, and safety warnings.

Integrated Furnace Control Menu

System Menu and Status Codes

Fault Code Recovery and Run Test Mode

Troubleshooting

Error Codes and IFC Layout

Explanation of error codes and diagram of IFC components.

Fault Code Troubleshooting

Flowcharts for diagnosing and resolving various furnace fault codes.

Sequence of Operation

Gas Heating Sequences

Cooling Sequences and Inducer Learning

Periodic Servicing Requirements