-5-
CRT/MK3
1 x Table top
4 x Legs, and fixing screws
4 x Leg rails
1 x Back fence and scale
2 x Fence cheeks
4 x Fence cheek knobs
1 x Top guard, top pressure and fixing knob
assembly
1 x Dust spout and fixing screws
2 x Back fence fixing knobs and bolts
1 x Side pressure and fixing knob assembly
2 x Edge planing rods
2 x Edge planing rod locking knob assemblies
16 x Leg rail fixing screws and nuts
1 x Insert plate and fixing screws
1 x No-volt release switch and fixing screws
1 x Mitre fence assembly
2 x Insert rings
1 x Lead-on pin
1 x Pushstick and pushstick park assembly bolts
2 x Table top scales (fitted)
4 x Bench mounting brackets and screws
2 x Cable management clips and screws
1 x Spanner 10mm A/F
1 x Hex key 3mm A/F
1 x Router screw fixing pack
1 x Instructions
1 x Guarantee card
Q Check for damage to the tool, parts or
accessories which may have occurred
during transport.
Q Take the time to thoroughly read and
understand this manual prior to operation.
ITEMS ENCLOSED
MARKINGS ON TABLE
The following pictures are shown on the tool.
Read instruction manual before use.
Date Code Position
The year of manufacture is on a label next to the
rating plate.
EC DECLARATION OF
CONFORMITY
MACHINERY DIRECTIVE
ROUTER TABLE
CRT/MK3
Trend declares that the attachment described
under Technical Data is in compliance with
2006/42/EC, and has been designed in
accordance with EN60745-1 Annex M,
EN 12100-1, EN 12100-2, EN 14121-1.
The tool also complies with Directive 2006/95/EC,
2004/108/EC (until 19.04.2016), 2014/30/EU
(from 20.04.2016) and 2011/65/EU.
Pushstick is made in compliance with Harmonized
Standard EN 1870-1.
For more information please contact Trend at the
following address or refer to back of manual.
The undersigned make this declaration on behalf
of Trend Machinery & Cutting Tools Ltd.
Managing Director
Jeff Willcocks
Trend Machinery & Cutting Tools Ltd
Unit 6 Odhams Trading Estate
St Albans Road, Watford
Herts, WD24 7TR
United Kingdom
01.04.2015
RESIDUAL RISKS
In spite of the application of the relevant safety
regulations and implementation of safety devices,
certain residual risks cannot be avoided. These
are:-
Q Impairment of hearing.
Q Risk of personal injury due to flying particles.
Q Risk of burns due to accessories becoming
hot during operation.
Q Risk of personal injury due to prolonged use
Information on Noise
The noise level when working can exceed 85
dB(A). Wear ear protection!
CRT/MK3
1 x Table top
4 x Legs, and fixing screws
4 x Leg rails
1 x Back fence and scale
2 x Fence cheeks
4 x Fence cheek knobs
1 x Top guard, top pressure and fixing knob
assembly
1 x Dust spout and fixing screws
2 x Back fence fixing knobs and bolts
1 x Side pressure and fixing knob assembly
2 x Edge planing rods
2 x Edge planing rod locking knob assemblies
16 x Leg rail fixing screws and nuts
1 x Insert plate and fixing screws
1 x No-volt release switch and fixing screws
1 x Mitre fence assembly
2 x Insert rings
1 x Lead-on pin
1 x Pushstick and pushstick park assembly bolts
2 x Table top scales (fitted)
4 x Bench mounting brackets and screws
2 x Cable management clips and screws
1 x Spanner 10mm A/F
1 x Hex key 3mm A/F
1 x Router screw fixing pack
1 x Instructions
1 x Guarantee card
Q Check for damage to the tool, parts or
accessories which may have occurred
during transport.
Q Take the time to thoroughly read and
understand this manual prior to operation.
ITEMS ENCLOSED
MARKINGS ON TABLE
The following pictures are shown on the tool.
Read instruction manual before use.
Date Code Position
The year of manufacture is on a label next to the
rating plate.
To Next Page
Loading...
