What does it mean when my Triumph Adler P-3525 MFP displays 'USB memory error. Job is canceled.'?
If your Triumph Adler All in One Printer displays 'USB memory error. Job is canceled.', this job is canceled. Press the OK key.
What to do if a paper jam occurs on my Triumph Adler P-3525 MFP All in One Printer?
If a paper jam occurs on your Triumph Adler All in One Printer, a message will be displayed about the jam and copying or printing will stop. Leave the power switch on and to remove the jammed paper refer to the following information below.
What does it mean when my Triumph Adler P-3525 MFP says 'Add toner'?
If your Triumph Adler All in One Printer displays the message 'Add toner' and the attention LED is lit, replace the toner container.
What to do if my Triumph Adler P-3525 MFP paper often jams?
If your Triumph Adler All in One Printer paper often jams, make sure you load the paper correctly. Also, if the paper is of the supported type but is in poor condition, remove the paper, turn it over, and reload it. Replace the paper with new paper if it is curled, folded, or wrinkled. Finally, remove any jammed paper from the machine.
What to do if my Triumph Adler P-3525 MFP All in One Printer cannot print?
If your Triumph Adler All in One Printer cannot print, ensure that the power cord is plugged into an AC outlet and the power switch is turned on. Check that the printer cable is securely connected and that the machine was powered on after connecting the printer cable. If the print job is paused, press [Resume] (the Left Select key) to resume printing. If there is an error message displayed, follow the corresponding procedure.
Why are my Triumph Adler P-3525 MFP All in One Printer printouts too dark?
If your Triumph Adler All in One Printer printouts are too dark, it could be because the machine is in Auto Density mode (set the correct density level for auto density) or the machine is in Manual Density mode (select the correct density level).
Why are blank sheets ejected from my Triumph Adler P-3525 MFP?
If blank sheets are ejected from your Triumph Adler All in One Printer, it may be because the originals are not loaded correctly. When placing originals on the platen, place them face-down and align them with the slit glass. When placing originals in the document processor, place them face-up.
What to do if my Triumph Adler P-3525 MFP All in One Printer copies have a moire pattern?
If your Triumph Adler All in One Printer copies have a moire pattern (dots grouped together in patterns and not aligned uniformly) and the original is a printed photograph, set the image quality to [Photo].
Why is my Triumph Adler All in One Printer not feeding originals?
If your Triumph Adler All in One Printer is not feeding originals, it may be because the originals are not placed correctly. When placing originals in the document processor, align the original width guides securely before placing the originals.
What to do if my Triumph Adler P-3525 MFP All in One Printer prints are dirty?
If your Triumph Adler All in One Printer prints are dirty, the platen or the document processor may be dirty. Clean the platen or the document processor.
General| Brand | Triumph Adler |
|---|---|
| Model | P-3525 MFP |
| Category | All in One Printer |
| Language | English |
Details the machine's operation panel keys and functions for navigation and control.
Identifies the main parts and external components of the machine.
Details the components and parts of the document processor unit.
Guides on selecting connection methods and preparing necessary cables.
Basic steps for initial machine setup, including power, language, and date/time.
Steps for network connectivity, software installation, and web server access.
Procedures for loading paper into cassettes/trays and placing originals for scanning.
How to log in to the machine using credentials and log out.
Step-by-step instructions for performing basic copying operations.
Instructions for printing documents from computer applications.
Procedures for sending scanned documents via E-mail, PC, or FTP.
Specifies the size of originals for scanning before starting the copying process.
Selects the paper source that contains the required paper size.
Allows combining 2 or 4 originals onto a single page for copying.
Function to save toner by reducing print quality for non-critical copies.
Selects the original size for scanning before starting the sending process.
Selects the size of the image to be sent.
Scans originals by automatically zooming depending on the sending size.
Selects the type and binding of original for duplex sending.
Prints files stored in USB memory directly without using a computer.
Stores scanned image files in USB memory connected to the machine.
Procedure to safely remove USB memory to avoid data damage.
Prints data stored on the machine's RAM disk from the operation panel.
Checks the status of jobs being processed or waiting to be printed.
Checks the history of completed jobs.
Pauses and resumes printing or waiting jobs.
How to cancel any print or send job that is currently being executed.
Includes settings for display, sound, date/time, and function defaults.
Settings for printer emulation, EcoPrint, and orientation.
Options for sending functions like key set and destination check.
Settings for Job Box features such as Quick Copy Jobs and retention.
Instructions for cleaning the machine's glass platen and document processor.
Procedure for replacing the toner container when it is empty.
General guidelines for identifying and resolving common machine problems.
How to interpret and respond to error messages displayed on the control panel.
Step-by-step instructions for clearing paper jams in various locations.
Specifies how user access is administered and enables/disables user login.
Manages copy/print counts by assigning IDs to accounts.
Checks the number of pages printed and scanned by various criteria.
To Next Page