5. Make sure garden hose is connectedto water inlet.
Checkthat high pressure hose is connected to spray
gun and pump. Turn on water.
NOTICE
You must attach all hoses before you start the engine.
Startingtheenginewithoutallthe hosesconnectedandwithout
thewaterturnedONwill damagethepump.
Damageto equipmentresultingfromfailureto followthis
instructionwillvoidwarranty.
6. Engagetrigger lock on spray gun and start engine
following instructions How to Start Your Pressure
Washer.
7. Apply detergentto a dry surface, starting at lower
portion of areato bewashed and work upward, using
long, even, overlapping strokes.
8. Allow detergent to "soakin" for 3-5 minutes before
washing and rinsing. Reappiyas neededto prevent
surfacefrom drying. DO NOTallow detergentto dry on
(prevents streaking).
IMPORTANT:You must flush the detergent siphoning
system after each use by placingthe filter into a bucket of
cleanwater, then Funthe pressure washer in low pressure
for 1-2 minutes.
PressureWasherRinsing
ForRinsing:
1. Engagetrigger lock on spray gun.
2. Removeblack spray tip from nozzleextension.
3. Selectand install desired high pressure spray tip
following instructions How to UseSpray Tips.
4. Keepspray gun a safe distance from areayou plan to
spray.
WARNING
Kickback spray gun can cause you to
from fall.
, Operatepressurewasherfroma stablesurface.
• Beextremelycarefulif youmustusethe pressurewasherfrom
a ladder,scaffolding,or anyothersimilarlocation.
• Firmlygraspspraygunwithboth handswhenusinghigh
pressuresprayto avoidinjurywhenspraygunkicksback.
5. Applya high pressuresprayto a small areaandthen
checksurface for damage.If no damageis found, you
canassumeit is okayto continuerinsing.
6. Startat top of areato be rinsed,working down with same
overlappingstrokesasyou usedfor cleaning.
Cleaning Detergent Siphoning Tube
If you usedthe detergent siphoning tube, you must flush it
with cleanwater before stopping the engine.
1. Placedetergent siphoning tube/filter in a bucket full of
cleanwater.
2. Engagetrigger lock on spray gun.
3. Removehigh pressure spray tip from nozzleextension.
4. Selectand install black detergent spray tip following
instructions How to Use Spray Tips.
5. Flush for 1-2 minutes.
6. Shut off engine following instructions How to Stop
Pressure Washerand turn off water supply.
7. ALWAYSpoint spray gun in a safe direction and
squeezespray gun trigger to release retained high
water pressure.
WARNING
Thehigh pressure stream of water that this
equipment produces can cut through skin and its
_ nderlying tissues, leading to serious injury and
)ossible amputation.
Spraygun traps high water pressure, even when
engine is stopped and water is disconnected,
which cancause injury.
, Keephighpressurehoseconnectedto pumpandspraygun
whilesystemis pressurized.
• ALWAYSpointspraygunin safedirectionandsqueezespray
guntrigger,to releasehighpressure,everytimeyoustop
engine.Engagetriggerlockwhennot in use.
IMPORTANT:Spray gun traps high water pressure, even
when engine is stopped and water is disconnected.
Automatic Cool Down System (Thermal Belief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reachtemperatures above
125°F.The system engagesto cool the pump by discharging
thewarm waterontotheground.
{'D
15
To Next Page
