TuffStuff TS-1000 - Introduction; About the Home Gym (TS-1000); Specifications; About the Icons

A
bout the Home Gym (TS-1000)
C
ongratulations on your new purchase of the Home Gym (TS-
000). This gym is capable of a variety of different exercises, as
w
ell as, smooth and user-friendly adjustment features. In addition,
h
is gym has been designed to meet the needs and performance
e
quirements for a suitable home exercise machine. We hope you
a
re completely satisfied with this product and wish you many years
o
f enjoyment.
T
uff Stuff Equipment
T
his Tuffstuff product has been built to precise quality standards
a
nd has been carefully packaged to ensure that damage will not
o
ccur during shipment. The Home Lifetime Warranty and signature
n
dicating final inspection has been conducted by our line foreman,
s
an expression of our confidence in the completeness, the
m
aterials, and workmanship of this product.
W
arranty
S
EE A COPY OF WARRANTY ON BACK PAGE.
R
egistration Card
T
o avoid unnecessary delays in warranty service and to insure that
a
permanent record of your purchase is on file with our factory, be
ure to complete the warranty registration card and send it to Task
n
dustries today.
Assembly Notes
1. Read and follow each step of this Assembly Instruction Manual
i
sequence. Do not skip ahead, as it will result in an improp
e
assembly or in having to disassemble parts later.
2. During the assembly of this unit you will be instructed to lea
v
some Hex Head Cap Screws loosely fastened. Naturally, th
e
will be fully fastened later in the assembly process. This is do
n
to prevent any difficulty with alignment of some parts during th
i
assembly.
Hardware Measurement Diagram
1
About the Icons
The icons displayed in this Owner’s Manual are used to facilitat
e
the correct assembly and safe use of this Product, as-well-as t
o
prevent injury to yourself or anyone else.
I
n
t
ro
d
uc
ti
on
Note: Due to continuing product improvements, specifications and designs are subject to chan
g
without notice.
Even though we have prepared this manual with extreme care, neither the publisher nor the auth
o
can accept responsibility for any errors in, or omission from, the information given.
P
rior to the Assembly of the TS-1000
1
. We advise you to consult your local Tuff Stuff retailer if you
should have a question or problem regarding the proper
assembly of this Home Gym.
2
. Consider the complete surface area of the TS-1000. Use the
overhead view on the front page for designing your layout before
assembling. Once the TS-1000 has been fully assembled it will
be heavy and difficult to move, therefore you should assemble
the TS-1000 in the area where it is to be used upon completion.
3
. It is recommended that another person assist you with the
assembly this unit.
4
. Neatly organize and identify all parts according to the Parts List
on page 31 and the Exploded View Diagram on fold-out page 32.
Tool Requirements
1. One 9/16” combination wrench
2. One 3/4” combination wrench
3. One 7/8” combination wrench
4. One 1/2” combination wrench
5. Two 7/16” combination wrenches
6. One ratchet
7. One 9/16” socket
8. One 3/4” socket
9. One rubber mallet
1
0. External retaining-ring pliers
1
1. Windex or household glass cleaner
1
2. One can silicone spray/ teflon spray lubricant
1
3. Multi-purpose grease
1
4. Measuring tape
1
5. Utility knife
S
pecifications
.Maximum Wt. Capacity - 200 Lbs. Fixed
. Total Machine Weight - 475 Lbs.
. Footprint (LWH) - See Front Cover
Note provides information necessary to properl
y
complete a procedure or information which wil
make the procedure easier to understand.
Caution indicates a potentially hazardous situa
-
tion, which, if not avoided, may result in minor o
r
moderate injury. It may also be used to aler
t
against unsafe practices.
Fully Fasten provides a instruction to fully fasten
(ex: completely tighten) a hardware assembly.
TS-1000 Home Gym w/Adjustable High-Low Pulley Syste
m
FULLY FASTE
N
CAUTION
LOOSELY FASTEN
NOTE:
Loosely Fasten provides a instruction to loosel
y
fasten (ex: hand tighten) a hardware assembl
y
only. This instruction is intended for the alignmen
t
of hardware components during the assembl
y
process.