Tylo SENSE COMBI ELITE Installation & User Guide

13
Figure 4: Other functions
1. Herb bowl
2. Fragrance holder/air humidi er
To create a pleasant fragrance in the sauna, pour a few drops of
T
yl Sauna Fragrance into the water in the fragrance holder.
ou can also mix a few drops of the sauna fragrance with water in
a sauna bucket and pour the water on fully heated stones. Use a
sauna ladle for pouring water on the hot stones.
our max. 1-2 ladles of water at a time, and then wait until the
stones have regained su󰀩 cient heat before pouring fresh water
on the stones again.
Tyl Sauna Fragrance comes in di󰀨 erent variants and fragrances.
2WKHUIXQFWLRQV
)UDJUDQFHKROGHU
DANGER! Fragrant essences etc. may ignite if
poured directly onto the stones.
12
DANGER! Never put fragrances in the herb bowl
or water reservoir.
+HUEERZO
A fragrant, refreshing herbal sauna can be created with fresh
or dried herbs or spices. Enjoy pleasant herbal fragrances in a
steamy tropical climate.
To create a fragrant sauna using fresh or dried herbs, put the
herbs in the herb bowl (see Figure 4).
TIP! Try di௺ erent combinations, such as birch,
lavender, mint, spices, tea bags and other exciting
fragrances.
86(
7KHFRQWUROSDQHOLQJHQHUDO
See instructions supplied with the control panel.
:
DWHUUHVHUYRLU
The sauna heater works with and without water in the tank.
When the water reservoir is in use, max. two out of three heater
elements in the stone compartment will be working. The heater
switches automatically between the reservoir and stone compart-
ment, depending on which setting has been set on the control
panel. See the instructions supplied with the control panel.
Filling the water reservoir:
efore starting the heater,  ll the water reservoir by carefully pour-
ing tap water through the herb grille, see  g. 3.
1. An empty reservoir is shown by two empty drop symbols on the
Elite control panel display (ure control panel shows a  ashing
drop symbol when the heater is operating). If the reservoir is emp-
ty when activating the main switch, three pulsing audio signals will
sound
2. When the water level reaches the safety sensor, a  lled drop
symbols will shown on the Elite control panel display (ure control
panel shows an unlit drop symbol). The heater element in the
reservoir can be started.
3. When the water level reaches the upper level sensor, two
 lled-in drop symbols will show on the Elite control panel display
(ure control panel shows unlit water drop). A continuous audio
signal will also sound for approx.: 2 secs, indicating that the water
level in the tank is full (in case you do not check the control panel
display during  lling).
Note! Do not add more water after the audio signal
to avoid the water boiling over and out of the reser-
voir.
Note! Never use salt water - can damage the heater
element in the reservoir. It can also cause a build
up of foam which causes the level sensor to detect
a higher water level than actual, and the heater ele-
ments can break.
Figure 3: Filling the water reservoir.
Water reservoir in operation:
1. When in use and if the water level drops below the upper level
sensor, it will continue to operate as normal but a single  lled-in
drop symbol will show on the Elite control panel display (ure
control panel shows unlit water drop). Water can be added, and a
steady audio signal will sound when the water level reaches full.
2. When in use and if the water level drops below the safety
sensor, three pulsing audio signals will sound and two empty drop
symbols will show on the Elite control panel display (ure control
panel shows a  ashing water drop when the heater is operating).
This indicates that there is insu󰀩 cient water in the reservoir, and
the heater element will automatically switch o󰀨 .

Tylo SENSE COMBI ELITE Specifications

General

Brand	Tylo
Model	SENSE COMBI ELITE
Category	Electric Heater
Language	English