Uniden OCEANUS DSC/ATIS User Manual

CONFIDENTIAL / Uniden Marine Dealers Only
TECHNICAL SERVICE INFORMATION Revised june 7 – 2005
Brand : UNIDEN Type: OCEANUS DSC/ATIS
1. MMSI
1A. After purchase the user can program, one time only, the MMSI in the radio.
This is described in the user manual.
1B. To reprogram the MMSI ID the radio needs to be serviced at a Uniden Marine
Dealer that has a RESET JIG. (also to reprogram ATIS ID)
This item can be purchased from Avera B.V. The Netherlands.
1C. Procedure to reset the radio for new MMSI ID:
1. Make sure power radio is off.
2. Connect the reset jig to the accessory cable of the radio.
(red arrows on connectors!)
3. Push and hold CH UP on the radio while turning power on.
4. If display reads: “MMSI ID CLR”
reset has been succesful and MMSI ID can be reprogrammed
5. If display reads: MMSI ID INIT
* the radio has not been initialized yet
* the reset jig is not connected properly
* the reset jig is broken
In this case: Put power off, wait some minutes and follow complete procedure
again. (See step 4)
Note: During testing the RESET JIG it happened that all MMSI numbers from the
directory were deleted!
2. ATIS ID
2A. How to program ATIS is not mentioned in the user manual !
2B.1. Situation “Out of the box”:
Put power on
Press “menu”” Display “DSC Call”
Press “CH Down” Display “SET UP”
Press “Select” Display “Directory”
Press 6x “CH Down (*1) Display “ATIS ID”
Press “Select” Display “AT “ and “ID 000000000”
The first number after “ID” is not blinking, than it is NOT possible to program an ATIS
number.

Uniden OCEANUS DSC/ATIS Specifications

General

Brand	Uniden
Model	OCEANUS DSC/ATIS
Category	Radio
Language	English

Summary

MMSI Programming and Reset

User MMSI Programming

User can program the MMSI one time only, as detailed in the user manual.

MMSI Reprogramming Service

Reprogramming MMSI ID requires service at a Uniden Marine Dealer with a RESET JIG.

Reset Procedure for New MMSI

Steps to reset the radio for a new MMSI ID using a reset jig and specific button presses.

Directory Data Loss Note

Testing the RESET JIG may result in the deletion of all MMSI numbers from the directory.

ATIS ID Configuration

ATIS Programming Overview

ATIS programming details are not mentioned in the user manual.

Initial ATIS Setup ('Out of the Box')

Procedure to check and program ATIS ID when the radio is new, via menu navigation.

ATIS Programming Procedure

Detailed steps to program the ATIS number using the microphone keypad after specific button presses.

Post-Programming Behavior

Describes the ATIS display and programmability status after the initial programming.

ATIS Reprogramming

Instructions for reprogramming the ATIS number, which is similar to the initial programming.

Reset Procedure for Blank ATIS

Steps to reset the radio for a blank ATIS ID (000000000) using a reset jig.

Editing New ATIS

Instructions for editing a new ATIS number, referencing the programming procedure.

Marine Radio Modes

Seagoing vs. Inland Waterway Mode

The radio can be switched between 'Seagoing Mode' and 'Inland Waterway Mode' using the PA/MODE button.

Inland Waterway Mode Indicator

The 'WX' indicator blinking on the display signifies that the radio is in 'Inland Waterway' Mode.

Extra Channel Enablement

Channel Activation Requirement

Activation of extra channels for licensed users requires a visit to a Uniden Marine Dealer.

Available Extra Modes

Details the four available extra modes: Mode 1 (L1/L2/F1/F2/F3) through Mode 4 (M1).

Procedure to Activate Extra Modes

Steps to activate extra modes by pressing specific buttons while powering on the radio.

UIC/Regional Frequency Charts

Mode Switching Capabilities

Radio can switch between Inland Waterways/Seagoing and International/USA/Canada frequency charts.

Procedure to Activate UIC

Steps to activate UIC modes by simultaneously pressing Select and HI/LO while turning power on.