D
Diana SalazarAug 8, 2025
What to do if UWE SEK-6000 Scales display shows a symbol?
- NNancy GreenAug 8, 2025
If the UWE Scales displays a symbol, it indicates a low battery warning. Recharge the battery to resolve this issue.
To Next PageTo Next PageWhat to do if UWE SEK-6000 Scales display shows a symbol?
If the UWE Scales displays a symbol, it indicates a low battery warning. Recharge the battery to resolve this issue.
Why is the weight not accurate on my UWE SEK-6000?
If your UWE Scales weight is not accurate, first check for any objects stuck on the scale and remove them. Also, external factors like wind or RF interference can cause this. Try using the scale in an environment free of such interference.
Why do UWE Scales turn off automatically?
The Auto Power Off function might be enabled on your UWE Scales. To change this setting, enter function F4.
What to do if UWE Scales display shows a low battery symbol?
If your UWE Scales display shows a low battery symbol, it means the battery is low. To resolve this, recharge the battery.
How to fix UWE Scales that cannot be turned on?
If your UWE Scales cannot be turned on, there might be several reasons: * The adaptor might not be plugged in correctly; re-plug it into the scale. * The rechargeable battery may be low; recharge it. * The adaptor voltage may be incompatible with the electrical outlet; replace the adaptor with one that has the correct voltage.
Keys used for inputting numbers for settings and functions like HI-OK-LO.
Function used for zeroing the scale or setting the OK value in HI-OK-LO.
Used within the counting function to sample the weight of items.
Press this key to tare off the weight of the load on the platter.
Turns the scale on or manually sets the display to zero; holds to control backlight.
Changes weighing units, resolution, and HI-OK-LO range settings.
Recalls the accumulated total weight or pieces from memory.
Accumulates the displayed weight or pieces into memory.
Sets the LO limit for the HI-OK-LO function.
Sets the HI limit for the HI-OK-LO function.
Clears previous HI-OK-LO settings: high limit, low limit, standard, and range.
Press this key to turn the scale off.
Indicates battery charging status (red for charging, green for fully charged).
Lights up when weight or pcs is lower than the set LO value for HI-OK-LO.
Lights up when weight or pcs is within the OK value range for HI-OK-LO.
Lights up when weight or pcs is higher than the set HI value for HI-OK-LO.
An arrow indicates a zero weight status on the scale.
An arrow indicates TARE function is active, showing NET weight.
Sign appears when battery is low; scale should be charged immediately.
An arrow indicates that the accumulation function is in use.
An arrow indicates that accumulation data is currently shown on the display.
This indicator shows the current weighing unit being employed.
Procedure to access internal functions by pressing TARE and ON/ZERO keys.
Sets the Auto Zero Tracking range (Zero_X) for automatic zeroing.
Displays the span value for scale calibration.
Shows software version and performs a full display test.
Displays default units and enables/disables units via MODE key.
Enables or disables the automatic power off function.
Configures RS-232 interface settings like Baud Rate and Parity.
Enables/disables digital filter to improve stability in noisy environments.
Selects RS-232 transmission mode: Auto, P-Out, or Conti.
Selects tare function mode: usable with unstable weight or only stable weight.
Configures sound alarm for HI, OK, LO, or HI/LO value reached.
Chooses relay output mode for Act L and Act H (open or closed).
Check adaptor connection, battery charge, and voltage compatibility.
Check Auto Power Off function settings.
Inspect for objects on scale, ensure level placement, and check for interference.
Calibrates the zero point of the scale with no load on the platter.
Calibrates the scale using a known weight (second point).
General
