© 2023 Veolia All Rights Reserved. Sievers TOC-R3 Analyzer Installation Guide DQS 95000-01 EN Rev. A
*Sievers is a trademark of Veolia and may be registered in one or more countries.
1
Installation Instructions
Customer Requirements:
Before starting the installation, ensure the following
items are acquired.
• Carrier Gas; CO concentration < 1 ppm,
Hydrocarbon concentration in the air < 0.1 ppm,
Moisture free and particle free.
Important!
See the “Warnings” section for additional important
information.
Secure all gas cylinders to an immovable
structure or permanent wall. Wear eye protection
when using compressed gases to avoid possible eye
injury. Only use regulators designed for use with the
selected gas. Store compressed gases in accordance
with all safety codes.
Sample Line pressure must not exceed 20 kPa (0.2
Bar, 2.9 psig).
To ensure proper operation and protect against injury,
do not operate the Analyzer with the covers o or
the door open.
A qualied Electrician must perform all electrical
installation activities.
All drain tubing and the vented drain must be
positioned lower than the level of the Analyzer to
minimize back pressure on the drain lines.
Always use ESD protection while working inside
the Analyzer and any Optional Accessories.
When handling components that contain sample,
standards, waste solution, or reagents, always wear
eye protection and gloves.
Always follow the manufacturer’s instructions
and SDS guidelines for preparation, handling,
and disposal of all standards, reagents, and
consumables.
Cautions
Save the original packing materials. If for any
reason you need to return the Analyzer, you MUST
pack the instrument in the original carton to ensure
that no damage occurs during shipment.
Use a 2-person lift. This instrument weighs over
18 kg (40 lb). It is the policy of OSHA and Veolia to
require a 2-person lift for items weighing over 18 kg
(40 lb).
Sievers* TOC-R3
Online TOC Analyzer
Installation Guide
Important!
Access the Operation and Maintenance Manual (referred
to as “Manual”) from www.sieversinstruments.com
[Customer Support > Sievers Analyzers & Instruments].
English
S
I
E
V
E
R
S
TO
C
-
R
3
O
n
l
i
n
e
T
O
C
A
n
a
l
y
z
e
r
• Options: Nitrogen, Zero/Synthetic Air, or Plant
Instrument Air (ANSI 7.0.01), Air Box Accessory.
• Pressure: 100-200 kPa (1-2 Bar, 14.5-29 psig)
• Flow Rate: 30-50 LPH
• Carboy (2 L, 0.55 US gal); for Acid
• Acid; Method dependent, use one of the following:
• 1-3% HCl (NPOC Mode)
• 1-3% HPO
• Small Funnel; 1 cm wide at smallest
•
• Tubing Cutter
• Ethernet Cable; optional.
If using Nitrogen or Zero/Synthetic Air
• Carrier Gas Tubing; 6 mm OD, 4 mm ID
If using Plant Instrument Air or Air Box Accessory
• Soda Lime; 700 g
• Granulated, 2-4 mm with indicator as CO
remover.
If using Dilution Water Feature, Optional
• Carboy (19 L, 5 US gal); for Dilution Water
• Dilution Water; DI Water or better, low TOC < 1
ppm
Additional Customer Requirements before
installation:
• If using an external air connection, there must be
an appropriate Pressure Regulator [Maximum of
installed near the Analyzer location.
• Each Sample Point (up to two) must have an
• The Analyzer must be installed within 2 m (6.6 ft.)
of the Sample Point(s).
• Veolia recommends that the Analyzer be connected
to an external switch or circuit breaker near the
Analyzer.
Analyzer Dimensions Weight:
Height: 900 mm
(35.5 in)
55 kg
(121.3 lb)
Width: 644.3 mm
(25.4 in)
Use a 2-person
lift!
Depth: 354.5 mm
(13.9 in)
To Next Page
Need help?
General
