Vicon KM 4000S - User Manual

Questions and Answers

A
Anthony BradfordAug 18, 2025
How to fix irregular stubble with Vicon KM 4000S Farm Equipment?
- C
  Cheryl MarquezAug 18, 2025
  To correct irregular stubble when using Vicon Farm Equipment, several factors should be checked. Ensure that the blades are not dull or bent by reversing or replacing them. Increase the PTO speed to 540 if it's too low, or slow down if the forward speed is too high. Also, verify that the blades are mounted in the correct rotating direction. If long material is wrapping around the drums, check the PTO rpm. Finally, consider fitting the wide inserts.
J
Jillian Mcgrath DDSAug 21, 2025
What to do if Vicon Farm Equipment has excessive vibration or noise?
- W
  William SanchezAug 21, 2025
  If your Vicon Farm Equipment is experiencing excessive vibration or noise, immediately stop the machine and inspect it to identify the cause before continuing work. Check that the coupling shafts are correctly mounted and that the correct coupling shaft is being used.
F
Felicia SuarezAug 23, 2025
Why does my Vicon Farm Equipment mower make too much noise when switched on?
- J
  Joseph Rich MDAug 23, 2025
  If your Vicon mower is making excessive noise when switched on, the tractor rpm may not match the mower rpm (540 rpm). Check that the tractor p.t.o rpm matches 540 rpm. Also, the RPM may be too high.
G
Gloria FoleyAug 26, 2025
Why does Vicon Farm Equipment machine take too much power?
- J
  Joshua AdamsAug 26, 2025
  If your Vicon Farm Equipment machine is consuming too much power, check the temperature of the boxes and cutter bar, as the oil level may be too high in the cutter bar or gearboxes. Also, check for and remove any rope coiled around the bearing house under the disc, and reduce driving speed if it's too high.
K
Keith JacksonAug 28, 2025
How to prevent blade breakage in stony areas with Vicon KM 4000S Farm Equipment?
- Z
  zmitchellAug 28, 2025
  To reduce regular blade breakage and excessive wear in stony areas when using Vicon Farm Equipment, ensure the cutter bar is as level as possible to prevent stones from being thrown into the machine. Try cutting higher using the accessory skids, and consider mounting the heavy-duty blades.
B
benitezcaitlinAug 30, 2025
Why are there waves in the cutting pattern of my Vicon KM 4000S Farm Equipment?
- Z
  zavalacynthiaAug 30, 2025
  Waves in the cutting pattern when using Vicon Farm Equipment can be due to excessive speed. Try slowing down. Additionally, the ground pressure may be too low; readjust it to the appropriate level.
J
Jennifer HendersonSep 1, 2025
What causes an irregular swath with Vicon KM 4000S?
- S
  Shannon GreenSep 1, 2025
  An irregular swath with Vicon Farm Equipment can result from crop accumulation on the skid; try lowering the PTO speed. If long material becomes wrapped around the drum, increase your driving speed. Also, consider fitting the wide inserts.
P
paula51Sep 4, 2025
Why is the manual disc rotation stiff on my Vicon Farm Equipment?
- A
  audreypenaSep 4, 2025
  If the manual disc rotation runs stiffly on your Vicon Farm Equipment, it could be due to several reasons. The disc guard might be bent upward too steeply, causing the disc to jam; return the disc guard to its correct position. Also, check for and remove any dirt or rope under the discs. Finally, ensure the knife bolt is mounted correctly.
A
abigailtorresSep 6, 2025
Why do the blades touch the discs on my Vicon KM 4000S?
- M
  Mike MccartySep 6, 2025
  If the blades are touching the discs on your Vicon Farm Equipment, it may be due to incorrect blade length. Ensure you mount blades of the correct length. Alternatively, the disc timing may be off, so time the discs accordingly.
T
Tanya LeSep 8, 2025
Why mowing unit wil not lift in a horizontal way on Vicon Farm Equipment?
- C
  Christian RodriguezSep 8, 2025
  If the mowing unit will not lift horizontally on your Vicon Farm Equipment, the ground pressure setting may be unequal on either side. Adjust the springs until the ground pressure is equal. Also, the long coupling shaft may have too high sliding resistance on the LH side of the mowing unit due to dry tubes; grease the tubes of the long coupling shaft.