Why won't my Vorwerk work after I exchanged the roller brushes?
If the device will not work after exchanging the roller brushes, check if the plug connection between the Electronic brush and the base device is correctly engaged. Also, place the roller brushes exactly onto the drive axles.
Why is the suction force declining in my Vorwerk kobold VK150 Vacuum Cleaner?
A decline in suction force in your Vorwerk Vacuum Cleaner is likely due to a full Premium Filter bag FP140/150. Replace the Premium Filter bag. It could also be that the suction channel is blocked; therefore, you should clean the suction channel of the Vacuum cleaner and/or any connected devices. Another cause may be an extremely dirty motor protection filter. In this case, you should clean or exchange the motor protection filter.
Why does my Vorwerk kobold VK150 Vacuum Cleaner change performance levels and get louder?
If your Vorwerk Vacuum Cleaner is setting itself to a different performance level and becoming louder, overheating may be the cause. This happens after prolonged use, with high ambient temperature, or when the filter bag is full or blocked, so the suction performance can no longer be regulated. Check the suction channel and connected accessory parts for blockages, and remove any obstructions. Exchange the Premium Filter bag if necessary and allow the motor to cool down.
How to stop my Vorwerk kobold VK150 Vacuum Cleaner from releasing an unpleasant odor?
If your Vorwerk Vacuum cleaner releases an unpleasant odor, it might be that the Premium Filter bag FP140/150 has lost its ability to retain odors, even if it's not full. Exchange the Premium Filter bag and insert a new Dovina fragrance chip. Also, thoroughly clean the suction channel of the Vacuum cleaner and/or the connected device, as well as the motor protection filter.
Why is my Vorwerk EB370 Electronic brush so loud?
If the Electronic brush is too loud, check if the roller brushes are correctly inserted, aligning them with the corresponding colored symbol (green to green), and always exchange both brushes. Only use original Kobold roller brushes. Remove any objects stuck around the roller brushes. Note that it can get noisy when used on hard flooring.
How to reattach the filter cover on my Vorwerk kobold VK150 Vacuum Cleaner?
To reattach the filter cover: Lay the Kobold VK150 Vacuum cleaner horizontally on the floor. Place the filter cover in a 60° angle onto the pivots of the device. Strongly push the filter cover with the studs into the pivots until they snap in with a click.
Why are the bristles of my Vorwerk Polsterboy deformed?
If the bristles of the Polsterboy are deformed or matted, it is because fringes or fabrics were sucked in and pulled again. Exchange the Suction nozzle.
Why doesn't my Vorwerk FK370 Freshener kit fit?
If the Kobold FK370 Freshener kit does not fit into the Electronic brush, it might have become warped as a result of being placed on a heater or in direct sunlight. Buy a new Freshener kit.
Why is my Vorwerk kobold VK150 not working?
If the device is not working, it might be that the connector plug of the connecting cable is not properly engaged. Ensure the connection has been established correctly (clicking).
Why is my Vorwerk Hard floor cleaner swiveling too much?
If the Hard floor cleaner is swiveling excessively, check whether the Cleaning cloth is sufficiently and evenly fixed at the Cloth holder. Also, check whether the Cloth holder has been inserted and latched into the Hard floor cleaner correctly. Only use original Cleaning cloths.
General| Type | Upright Vacuum Cleaner |
|---|---|
| Model | VK150 |
| Power | 700 W |
| Filtration System | HEPA Filter |
| Noise Level | 78 dB |
| Accessories | Upholstery brush, Crevice nozzle |
Defines appropriate and restricted uses of the vacuum cleaner and accessories.
Details risks like electric shock, fire, explosion, injury, pinching, choking, and allergy issues.
Explains warning symbols and signal words for different hazard levels.
Instructions on connecting vacuum cleaner to various accessory parts.
Steps for connecting the power cord and winding/unwinding.
How to turn the device on/off and set the power level.
Solutions for common problems with the main vacuum unit.
Troubleshooting specific problems with the EB370 electronic brush.
Solutions for faults related to the SP530 hard floor cleaner.
To Next Page