Vorwerk KOBOLD VK200 User Manual (English)

Questions and Answers:

J
Jaime JeffersonSep 2, 2025
Why does my Vorwerk DuoClean switch off, the 'STOP' light flashes red, and the Vacuum Cleaner turns off?
- L
  Leah AliSep 2, 2025
  If the DuoClean switches off, the operating display light “STOP” flashes red, and the Upright Vacuum Cleaner switches off simultaneously, it's possible that moisture has been sucked in. Turn off the Upright Vacuum Cleaner and allow the device to dry completely. Afterward, switch on the Upright Vacuum Cleaner and close the secondary air flap of the DuoClean. This may need to be repeated.
M
michellecarpenterAug 31, 2025
What to do if LED rows do not light up green after inserting a new Premium Filterbag in my Vorwerk Vacuum Cleaner?
- E
  Edward SandovalAug 31, 2025
  If, after inserting a new, banded Premium Filterbag into your Vorwerk Vacuum Cleaner, the LED rows don't light up green, the bands of the filter bag may not have been severed. Open the filter cover and check if the bands have been cut by the closure of the filter cover. If not, cut the bands by hand and close the cover again.
J
Jodi LewisAug 30, 2025
Why does the Automatic Electric Brush of my Vorwerk KOBOLD VK200 Vacuum Cleaner switch off and the operating display flashes red?
- M
  Michael StewartAug 30, 2025
  If the Automatic Electric Brush switches itself off and the operating display flashes red, a vacuumed object or threads may be blocking the brush. Switch off the device, unplug it, and remove any obstructing objects. If threads are the issue, cut them.
S
Sarah WilkinsonAug 29, 2025
What to do if the filter cover of my Vorwerk KOBOLD VK200 has become detached?
- D
  Dr. Monica AustinAug 29, 2025
  If the filter cover has become detached from your Vorwerk Vacuum Cleaner, it might be because you bumped against the opened cover. Reinsert the cover by setting it onto the hinges of the device and pushing it shut until the cover latch engages. Also, make sure that the filterbag is correctly inserted.
R
Robert MaxwellAug 27, 2025
Why does my Vorwerk Vacuum Cleaner change power levels and get louder?
- M
  Mr. Seth Johns PhDAug 27, 2025
  If your Vorwerk Vacuum Cleaner changes power levels and gets louder, it may be overheating due to prolonged use, high ambient temperature, or a full/blocked 3in1 Premium Filterbag. Check the suction channel and any connected accessory heads for blockages, and replace the filterbag if necessary. Allow the motor to cool down. This can also occur when switching from hard floors to carpeting or when using the automatic suction power setting.
C
Chad SmithAug 26, 2025
Why is the Automatic Electric Brush of my Vorwerk KOBOLD VK200 hard to push?
- S
  Shannon BraunAug 27, 2025
  If the Automatic Electric Brush is hard to push, it could be due to the power performance level being too high. Try setting the device to a lower power performance level using the main switch on the handle of the Upright Vacuum Cleaner, or use the 'auto' power performance level. It’s also possible that the Automatic Electric Brush is in manual operating mode; switch the Upright Vacuum Cleaner off and back on again.
D
Donna LopezAug 25, 2025
Why does my Vorwerk Vacuum Cleaner release an unpleasant odor?
- B
  Brian MartinAug 26, 2025
  If your Vorwerk Vacuum Cleaner is releasing an unpleasant odor, the 3in1 Premium Filterbag FP200 may have lost its ability to retain odors, even if it's not full. To resolve this, replace the 3in1 Premium Filterbag and insert a new Dovina fragrance chip. Additionally, thoroughly clean the suction channel of the vacuum cleaner and any connected devices, as well as the motor protection filter.
M
Melissa CarterAug 23, 2025
What to do if my Vorwerk KOBOLD VK200 Vacuum Cleaner doesn’t run and the LEDs flash red?
- D
  Daniel BoyerAug 23, 2025
  If your Vorwerk Vacuum Cleaner doesn’t run and the LEDs flash red, it could be due to a few reasons: * The telescopic handle may not have been mounted correctly during initial setup, preventing electrical connection. In this case, pull out the mains plug and extend the handle again until it locks into place. * The device may have overheated. Pull out the mains plug, let the device cool down, and try again.