Why is my Watts Water Filtration System producing water slowly?
Slow water production in your Watts Water Filtration System can be due to several reasons: low water pressure, crimped tubing, clogged pre-filters, or a fouled membrane. To address this, you can add a booster pump to increase water pressure, ensure the tubing is straight without any crimps, replace the pre-filters, or replace the membrane.
What to do if my Watts Water Filtration System water tastes or smells bad?
If the water from your Watts Water Filtration System has an offensive taste or smell, it could be due to a depleted post carbon filter, a fouled membrane, or residual sanitizer that wasn't fully flushed out. You can try replacing the post carbon filter or the membrane. Also, drain the storage tank and refill it overnight.
Why is there only a small amount of water from my Watts Water Filtration System storage tank?
If your Watts Water Filtration System is producing only a small amount of water, it could be because the system is just starting up or the air pressure in the storage tank is low. It normally takes 2-3 hours to fill the tank. Low water pressure and/or temperatures can reduce production rate. Try adding pressure to the storage tank; the pressure should be 8-10 psi when the tank is empty.
What to do if my Watts Water Filtration Systems has leaks?
Leaks in your Watts Water Filtration System can occur if fittings are not tightened, if an O-ring is twisted, or if there's misalignment of the hole in the drain saddle. To fix this, tighten the fittings as necessary, replace any twisted O-rings, and realign the drain saddle.
How to fix noise from the faucet of my Watts Water Filtration System?
Noise from the faucet of your Watts Water Filtration System can be caused by the air gap faucet location, the drain saddle, or a restriction in the drain line. The noise should disappear after the system shuts down. Relocate the drain to above the water trap. Blockage is sometimes caused by debris from garbage disposal or dishwasher.
Why is the water from my Watts Water Filtration System milky colored?
Milky colored water in your Watts Water Filtration System is a normal occurrence when initially starting up the RO system. This milky look will disappear during normal use within 1 to 2 weeks.
What to do if there is no drain water from my Watts Water Filtration System?
If there is no drain water from your Watts Water Filtration System, it is likely due to a clogged flow restrictor. To resolve this, replace the flow restrictor.
Details the stages, operating pressure, and temperature for the 315 model.
Lists Watts item numbers, descriptions, and service life for 315 model parts.
Details the stages, operating pressure, and temperature for the 415 model.
Lists Watts item numbers, descriptions, and service life for 415 model parts.
Details the stages, operating pressure, and temperature for the 525 model.
Lists Watts item numbers, descriptions, and service life for 525 model parts.
Details the stages, operating pressure, and temperature for the 525P model.
Lists Watts item numbers, descriptions, and service life for 525P model parts.
Provides step-by-step instructions and diagrams for making secure tube connections.
Instructions for connecting the RO system to a non-air gap faucet.
Instructions for connecting the RO system to an air gap faucet.
Guides on installing the drain saddle for waste water discharge.
Instructions for mounting the drain clamp on the drain pipe.
Detailed steps for cleaning the RO storage tank with disinfectant.
Recommendations for storing and maintaining RO system filters.
Guidelines for maintaining the RO membrane's performance and lifespan.
Step-by-step guide for replacing RO system filters and membranes.
Replacement parts list for the Watts RO System Model 315.
Replacement parts list for the Watts RO System Model 415.
Replacement parts list for the Watts RO System Models 525 and 525P.
General| Model | 315 |
|---|---|
| Stages | 1 |
| Operating Temperature | 40 - 100 °F |
| Filtration Method | Sediment Filtration |
| Operating Pressure | 25-100 psi |
| Type | Whole House Water Filtration System |
To Next Page