wattstopper DW 100 - User Manual

Wattstopper
®
Dual Technology Wall Switch Occupancy Sensors (version 3)
Interrupteur mural avec détecteurs de mouvement à technologie double (v3)
Sensores de ocupación e interruptor de pared con tecnología doble (v3)
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 24000 – 12/16 rev. 1
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: DW-100/DW-100-347/DW-200
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Voltages:
DW-100 & DW-200................................ 120/277VAC, 50/60Hz
DW-100-347 ................................................. 347VAC, 50/60Hz
Load Limits for each relay:
@120VAC .........................0-800W tungsten or ballast, 1/6 HP
@277VAC .......................................................0-1200W ballast
@347VAC .......................................................0-1500W ballast
Load Type Compatibility:
Incandescent, fluorescent, magnetic or electronic ballast
Horsepower Rating (each relay) .................. 1/6 HP @120VAC
Time Delay Adjustment ............................................ 5 to 30 minutes
Walk-Through Mode ........... 3 minutes if no activity after 30 sec.
Test Mode .................. 5 sec. for 10 min. with DIP switch setting
PIR Adjustment ............................................ High or Low (DIP switch)
Ultrasonic Adjustment .................Minimum to Maximum (trimpot), Off
Frequency ..........................................................................40kHz
Light Level Adjustment ................................................. 8fc to 180+fc
Alerts ................................................................... Selectable Audible
US Patents: 5640113, 6617560
DW 100 DW-100-347
DW-200
DESCRIPTION AND OPERATION
The DW Dual Technology Wall Switch sensors combine advanced passive infrared (PIR) and ultrasonic technologies into one unit. The
combined technologies help to eliminate false triggering even in difficult applications.
Selectable operating modes allow the sensor to turn a load ON, and hold it ON as long as either or both technologies detect occupancy.
After no movement is detected for the selected time delay, the lights switch OFF. A “walk-through” mode can turn lights off after only 3
minutes, if no activity is detected after 30 seconds following an occupancy detection.
The DW-100 has one relay and one ON/OFF button. The DW-200 contains two relays and two ON/OFF buttons to allow control of one
or two loads independently. Pressing a button toggles the state of the corresponding relay.
DW sensors contain a light level sensor. If adequate daylight is present, the sensor holds the load OFF until light levels drop, even if the
area is occupied. In the DW-200, light level only affects the load on Relay 2. Users can overrule this function by pressing the ON/OFF
button. See Light Level Adjustment.
Turning ON the Load (ON Mode)
The relays are programmed independently for either Auto ON or Manual ON. In either mode, the load can be turned ON or OFF using
the ON/OFF button.
Manual ON
DIP 8 ON for Relay 1
DIP 9 ON for Relay 2
With an ON Mode DIP switch in the ON position, the occupant must press the ON/OFF button to turn
ON the load. The sensor keeps the load ON until no motion is detected for the selected time delay.
There is a 30 second re-retrigger delay. If occupancy re-triggers during the delay (see Trigger Mode),
the sensor turns the load back ON. After the re-trigger delay elapses the ON/OFF button must be
pressed to turn ON the load.
Auto ON
DIP 8 OFF for Relay 1
DIP 9 OFF for Relay 2
With an ON Mode DIP switch in the OFF position, the load turns ON and OFF automatically based on
occupancy. If the load is turned OFF manually, Presentation Mode operation applies. This prevents
the load from turning ON automatically after it was deliberately turned OFF. Pressing the button to turn
lights ON returns the sensor to Auto ON mode.
Model # Relay Default ON Mode DIP Switch # Setting
DW-100 1 Manual ON 8 ON
DW-100-347 1 Manual ON 8 ON

Summary

Specifications

Description and Operation

Turning ON the Load (ON Mode)

Explains manual and auto modes for turning loads ON and OFF based on occupancy detection.

Configuration and Modes

Presentation Mode

Feature that holds lights OFF after manual OFF until subsequent occupancy.

Time Delays

Sets the duration the load remains ON after no motion is detected.

Walk-Through Mode

Shortens delay to reduce ON time after brief occupancy; exits immediately.

PIR Sensitivity Adjustment

Optimizes PIR detection by adjusting sensitivity for ambient conditions.

Alerts

Provides audible warnings before the load turns OFF.

Trigger Mode

Defines how occupancy is detected (PIR, Ultrasonic, or both).

Installation and Coverage

Coverage Patterns

Details PIR and Ultrasonic sensor coverage areas and testing guidelines.

Installation Instructions

Step-by-step guide for wiring and mounting the occupancy sensors.

Settings and Adjustments

DIP Switch Settings

Configuration options for time delay, trigger mode, and on modes via DIP switches.

Sensor Adjustments

Fine-tuning sensor behavior including light level and reset options.

Light Level Adjustment

Enables light level control to hold loads OFF until daylight drops.

Reset to Default

Restores factory settings and disables light level control.

Service Mode

Accesses advanced service functions by adjusting the ultrasonic trimpot.

Troubleshooting

Cover Plates

Information on compatible decorator-style switch cover plates and colors.

wattstopper DW 100 Specifications

General

Brand	wattstopper
Model	DW 100
Category	Accessories
Language	English