Weed Eater 1700 - Pre-Operation Checks; Starting Instructions

a. USE THE FOLLOWING FUEL MIXTURES
2. HOW TO MIX FUEL
1 GALLON
REGULAR
LEADED
OR
UNl-EADED
GASOLINE
2 (TWO)
GALLONS
REGULAR
LEADED
OR
UNLEADED
GASOLINE
1.)
+
2.)
+
POULAN/WEED EATER
16:1
ENGINE OIL
- OR -
ANY GOOD GRADE
16:1
AIR-COOLED, 2-CYCLE
ENGINE OIL
POULAN/WEED EATER
32:1
ENGINE OIL
CORRECT
FUEL MIX
CORRECT
FUEL MIX
CAUTION:| If you use a 32:1 fuel mix, you
must use Poulan/Weed Eater 32:1 Engine Oil
or engine damage can occur.
a. Pour one-half of the gasoline into an ap
proved, marked container. Do not try to
mix oil and gasoline directly in the fuel
tank.
b. Add entire measure of 2-cycie Engine Oil.
c. Mix.
d. Add remainder of gasoline.
e. Mix thoroughly for one minute.
3. IMPORTANT POINTS TO REMEMBER
a. Use only recommended fuel mixtures.
b. Eliminate all sources of sparks or flame in
the areas where fuel is mixed, poured or
stored. There should be no smoking, open
flames or work that could cause sparks.
b. DO NOT USE:
AUTOMOTIVE
OIL
PREMIUM or
ETHYL
GASOHOL
Does not have proper additives
for 2-cycie engines and couid
cause damage.
Burns too hot for 2-cycie
engines; wiil shorten spark
piug iife and can damage your
engine.
Aicohoi absorbs moisture
causing acids to form which
wiil damage metai and rubber
parts.
c. Mix and store fuel in an approved, marked
container.
d. Mix and pour fuel in a well-ventilated area.
Gasoline vapors are harmful to your health
and are a serious fire hazard.
e. Avoid over filling the fuel tank. Allow 3/4
inch for expansion. Tighten Fuel Cap
securely.
f. Wipe up all fuel spills before starting the
engine.
g. Move at least 10 feet (3 meters) away from
fuel and fueling site before starting the
engine.
PRE-OPERATION CHECKS
Before operating your unit, always:
1. (/'CHECK OVER SAFETY RULES AND PRE
CAUTIONS in this Operator's Manual. Make
certain you completely understand and can
follow each one.
2. /check the unit for loose bolts,
NUTS, OR FITTINGS. Tighten, repair or replace
3.
4.
parts as necessary. Use only genuine WEED
EATER® replacement parts that are identical
to the original parts.
/CHECK THE AIR FILTER. Clean the filter
before operating the unit.
/CHECK THE FUEL TANK. Fill with a clean,
fresh fuel mixture acording to instructions in
fuel mixture section.
C. STARTING INSTRUCTIONS
• Extend a minimum of 2 inches of line from
the cutting head before the engine is started.
This provides the correct load on the engine.
Figure 3, page. 5.
• Place the cutting head on the ground away
from trees, bushes, onlookers, etc. while the
engine is being started.
• Pull the starter rope quickly and sharply us
ing no more than 12-15 inches of rope with
each pull. If you use the full length of starter
rope, you can break it.
• Lift the unit off the ground quickly when the
engine runs.
• Pull the starter rope no more than 10 times to
avoid flooding the engine, if flooding occurs,
push choke knob in fully and pull starter rope
sharply until engine runs.
• Stop the engine by pressing the "OFF" but
ton (Figure 9) or by pulling the choke knob to
full choke position (Figure 6). Moid button
down until engine stops.