This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 17 for
important information about how to get the most benefit from your exercise program. Also, refer to the accompa-
nying exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time you use the resistance system. Replace worn parts immedi-
ately. The resistance system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use
solvents. The crossbows can be cleaned with a vinyl and rubber protectant, available at an automotive or depart-
ment store.
13
Ball
ATTACHING THE HIGH PULLEYS AND LEG LEVER
To use a high pulley, slide the hook on the High
Pulley Housing (21) onto an Eyebolt (34). Attach the
end of the Short Cable (33) without the ball to the end
of the Long Cable (80) with a Cable Clip (51). Attach
the other high pulley in the same manner.
To use the Leg Lever (not shown), attach the two
ends of the Leg Lever Cable (32) to the ends of the
Long Cable (80) with two Cable Clips (51).
Remove the high pulleys, and detach the Leg Lever
Cable (32), when not in use. Store the ends of the
Leg Lever Cable on the Hook (104) under the Bench
Rail (not shown).
33
21
51
51
104
80
32
34
ADJUSTMENTS
ADJUSTING THE SEAT
The Seat (13) can be secured in any of five positions
on the Bench Rail (5). To move the Seat, pull the
Seat Knob (45) out as far as it will go, and slide the
Seat to the desired position. Engage the Seat Knob
into an adjustment hole in the Bench Rail.
To perform row exercises, the leg press strap must be
attached to the long cable (see ATTACHING THE
ACCESSORIES, on page 14), and the Seat Carriage
(12) must be able to roll along the Bench Rail (5).
First, remove the Backrest (14) from the Seat
Carriage (see ADJUSTING THE BACKREST on page
15). Then, pull the Seat Knob (45) out as far as it will
go, and turn the Knob so that the pin rests at the end
of the “L”-shaped slot (see the inset drawing).
13
14
12
5
8
12
45
Pin
“L”-Slot
9. Press two 38mm Round Inner Caps (38) into the
ends of the Lat Tower Crossbar (10).
Attach two Eyebolts (34) to the Lat Tower
Crossbar (10) with two M8 Washers (59) and two
M8 Nylon Locknuts (65). Do not overtighten the
Locknuts; the Eyebolts must be able to rotate
freely.
Attach the Lat Tower Crossbar (10) to the Lat
Tower (4) with two M10 x 65mm Button Head
Screws (70), two M10 Washers (75), and the
Crossbar Cover (93). Be sure that the Eyebolts
(34) are oriented as shown in the inset draw-
ing. If they are not, turn the Lat Tower
Crossbar around and reattach it.
9
38
65
65
10
34
59
34
70
59
93
75
4
38
34
10
4
Side View
10. Attach the two 10-pound Short Crossbow Caps
(20) to the 10-pound centre Crossbow (44) with
two M4 x 12mm Flat Head Screws (85).
Using ten M4 x 12mm Flat Head Screws (85),
attach the two 10-pound Crossbow Caps (101) to
the 10-pound Removable Crossbow (67), the two
20-pound Crossbow Caps (88) to the 20-pound
Removable Crossbow (36), the four 80-pound
Crossbow Caps (100) to the two 80-pound
Crossbows (95), and the two 40-pound Crossbow
Caps (79) to the 40-pound Crossbow (96).
10
79
88
101
20
100
67
36
95
96
85
85
85
85
85
44
11
86
72
Rings on
this side
96
95
95
44
36
67
18
Rods
Edges
up
35
18
4
11. Locate the Crossbow Fulcrum (18) on the Lat
Tower (4) (see the inset drawing). Slide the
Crossbow Spacer (35) onto the rods on the
Crossbow Fulcrum. Make sure the Spacer is
oriented as shown in the drawing.
Set the Crossbows into the Crossbow Spacer (35)
in the following order: the 10-pound Removable
Crossbow (67), the 20-pound Removable
Crossbow (36), an 80-pound Crossbow (95), the
10-pound centre Crossbow (44), an 80-pound
Crossbow (95), and the 40-pound Crossbow (96).
Make sure the indicated rings are on the side
shown and the arrows point toward the Spacer.
Attach the Crossbow Cover Plate (72), with the
edges up, to the Crossbow Spacer (35) with two
M8 x 19mm Button Head Screws (86).
To Next Page
Loading...
