220
SECTION1 SAFETYPRECAUTIONS
SECTION1CONSIGNESDESÉCURITÉ
1-1. Symbol Usage Symboles utilisés
Means Warning! Watch Out! There are possible
hazards with this procedure! The possible hazards
are shown in the adjoining symbols.
Symbole graphique d’avertissement ! Attention !
Cette procedure comporte des risques
possibles ! Les dangers éventuels sont représentés par les
symboles graphiques joints.
Marks a special safety message.
Indique un message de sécurité particulier
Means “Note”; not safety related.
Signifie NOTE ; n’est pas relatif à la sécurité.
This group of symbols means Warning! Watch Out
possible ELECTRIC SHOCK, MOVING PARTS, and
HOT PARTS hazards. Consult symbols and related
instructions below for necessary actions to avoid the
hazards
Ce groupe de symboles signifie Avertissement! Attention!
Risques d’ÉLECTROCUTION, ORGANES MOBILES et
PARTIES CHAUDES. Consulter les symboles et les
instructions afferents ci-dessous concernant les
mesures à prendre pour supprimer les dangers.
1-2. Arc welding Hazards Dangers relatifs au soudage à l’arc
The symbols shown below are used throughout
this manual to call attention to and identify possible
hazards. When you see the symbol, watch out, and
follow the related instructions to avoid the hazard.
Only qualified persons should service, test,
maintain, and re- pair this unit.
During servicing, keep everybody, especially
children, away
Les symboles représentés ci-dessous sont utilisés
dans ce manuelpour attirer l’attention et identifier
les dangers possibles. Enprésence de l’un de ces
symboles, prendre garde et suivre lesinstructions
afférentes pour éviter tout risque. Les instructions
enmatière de sécurité indiquées ci-dessous ne
constituent qu’un sommaire des instructions de
sécurité plus complètes fournies dans les normes
de sécurité énumérées dans la Section 2-5. Lire et
observer toutes les normes de sécurité.
Seul un personnel qualifié est autorisé à installer,
faire fonctionner, entretenir et réparer cet appareil.
Pendant le fonctionnement, maintenir à distance
toutes les personnes, notamment les enfants de
l’appareil.
ELECTRIC SHOCK can kill.
UNE DÉCHARGE ÉLECTRIQUE
entraîner la mort.
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body
protection.
Insulate yourself from work and ground using dry
insulating mats or covers big enough to prevent any
physical contact with the work or ground.
Do not use AC output in damp areas, if movement is
confined, or if there is a danger of falling.
Use AC output ONLY if required for the welding
process.
If AC output is required, use remote output control if
present on unit.
Additional safety precautions are required when any of
the following electrically hazardous conditions are
present: in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings, or
scaffolds; when in cramped positions such as sitting,
kneeling, or lying; or when there is a high risk of
unavoidable or accidental contact with the workpiece or
ground. For these conditions, use the following
equipment in order presented: 1) a semiautomatic DC
constant voltage (wire) welder, 2) a DC manual (stick)
welder, or 3) an AC welder with reduced open-circuit
voltage. In most situations, use of a DC, constant
voltage wire welder is recommended. And, do not work
alone!
Disconnect input power or stop engine before installing
or servicing this equipment. Lockout/tagout input power
according to OSHA 29 CFR 1910.147 (see Safety
Standards).
Properly install and ground this equipment according to
its Owner’s Manual and national, state, and local
codes.
Always verify the supply ground − check and be sure
that input power cord ground wire is properly connected
to ground terminal in disconnect box or that cord plug is
connected to a properly grounded receptacle outlet.
When making input connections, attach proper
grounding conductor first − double-check connections.
Frequently inspect input power cord for damage or bare
To Next Page
Loading...