To Next PageTo Next PageWhy does my Westinghouse iGen2200 start then shut down?
If your Westinghouse Portable Generator starts and then shuts down, it could be due to several reasons. First, check if you are out of fuel and refuel if necessary. Also, check the engine oil level and ensure it is correct. A dirty air filter can also cause this issue, so clean it. If the fuel is contaminated, drain the fuel tank and refuel with fresh gasoline.
Why does my Westinghouse iGen2200 engine lack power?
If your Westinghouse Portable Generator engine lacks power, it could be due to a restricted air filter. Clean or replace the air filter. Another cause could be bad fuel; if the generator was stored without treating or draining gasoline, or refueled with bad gasoline, drain the fuel tank and refuel with fresh gasoline.
What to do if my Westinghouse Portable Generator runs rough when load applied?
If the engine of your Westinghouse Portable Generator runs rough or bogs when a load is applied, it could be due to a dirty air filter, so you should clean it. The generator might also be overloaded, so unplug some devices. A faulty power tool or appliance could also be the cause; try replacing or repairing the tool or appliance, then stop and restart the engine.
What to do if my Westinghouse Portable Generator engine stops?
If your Westinghouse Portable Generator engine stops during operation, start by checking the fuel level and adding fuel if necessary. Ensure the fuel isn't contaminated; if it is, drain and refill with fresh fuel. Verify the fuel cap vent and fuel control switch are in the ON position. Also, check the oil level and add oil if needed. Make sure the spark plug boot is firmly connected to the spark plug. If there's an overload, disconnect all electrical cords and devices, restart the generator with the ECO throttle switch OFF, and reconnect loads individually. Check the power demands of each load against the generator's AC output rating. If the issue persists after checking these, consult an authorized Westinghouse service dealer.
Why does my Westinghouse iGen2200 have no 240-Volt AC output?
If your Westinghouse Portable Generator's engine is running but there's no 240-Volt AC output, first check if the output indicator light is green. If so, inspect the connected electrical cords and appliances. Ensure the cord or appliance plug is fully inserted into the 240-Volt AC outlet. Try connecting a known working appliance to verify the electrical output. If the output indicator light isn't lit, and the overload alarm is red, disconnect all devices, press the reset button (iGen4500s only), and restart the engine with the ECO throttle switch OFF. Reconnect loads individually to identify any faulty or overloading devices. If the overload alarm is not illuminated, the generator may be faulty. If problems persist, take the generator to an authorized Westinghouse service dealer.
How to fix a Westinghouse iGen2200 Portable Generator that runs erratically?
If your Westinghouse Portable Generator runs erratically, it could be due to varying power demands from connected devices, which is normal, especially with the ECO throttle on. If both the output indicator and overload alarm are lit, switch off or unplug devices to reduce the load. Ensure the engine is warm enough by letting it run for at least 2 minutes after moving the choke to the RUN position, and make sure the choke isn't in the START position when the engine is warm. Also, check for stale or contaminated fuel and clean the air filter if it's dirty. If the problem continues, seek assistance from an authorized Westinghouse service dealer.
What to do if the electric starter on my Westinghouse iGen2200 iGen4500s won't crank?
If the electric starter on your Westinghouse iGen4500s Portable Generator isn't cranking the engine properly, first disconnect any electrical devices. If the battery is flat, try starting the engine manually or recharge the battery using an external charger. If the battery is faulty, replace it. Also, ensure the remote control fob is within range and has a clear line of sight to the generator; replace the remote's battery and pair it with the generator if needed. If these steps don't resolve the issue, the generator may be faulty, and you should take it to an authorized Westinghouse service dealer.
Why is there no DC output from my Westinghouse iGen2200 Portable Generator?
If your Westinghouse Portable Generator is running but has no 5 or 12-Volt DC output, first check that the electrical cord or appliance plug is fully inserted into the DC outlet. If it is, test the appliance with a known working one to verify the electrical output. Also, check for any overload or short circuit in the connected DC load. Disconnect all devices, restart the engine with the ECO throttle switch OFF, and ensure the DC devices do not overload the generator's rated DC output. If problems persist, the generator may be faulty, and you should consult an authorized Westinghouse service dealer.
General| Running Watts | 1800 |
|---|---|
| Peak Watts | 2200 |
| Fuel Type | Gasoline |
| Tank Capacity | 1.2 gallons |
| Run Time at 25% Load | 12 hours |
| Noise Level | 52 dBA |
| Parallel Capable | Yes |
| Inverter | Yes |
| Run Time at 50% Load | 8 hours |
| Starting System | Recoil |
| Frequency | 60 Hz |
| Engine | 79cc Westinghouse OHV 4-Stroke |
| Weight | 46.3 lbs |
| Outlets | 2 x 120V 20A, 2 x USB |
| Dimensions | 19.8 x 11.4 x 17.9 inches |
