Westinghouse iGen4500s

Questions and Answers

V
Veronica LewisAug 22, 2025
What to do if my Westinghouse Portable Generator engine stops?
- S
  Stephanie WoodAug 22, 2025
  If your Westinghouse Portable Generator engine stops during operation, start by checking the fuel level and adding fuel if necessary. Ensure the fuel isn't contaminated; if it is, drain and refill with fresh fuel. Verify the fuel cap vent and fuel control switch are in the ON position. Also, check the oil level and add oil if needed. Make sure the spark plug boot is firmly connected to the spark plug. If there's an overload, disconnect all electrical cords and devices, restart the generator with the ECO throttle switch OFF, and reconnect loads individually. Check the power demands of each load against the generator's AC output rating. If the issue persists after checking these, consult an authorized Westinghouse service dealer.
J
Joseph PadillaAug 26, 2025
Why does my Westinghouse iGen4500s Portable Generator have no 240-Volt AC output?
- A
  Ana DaviesAug 26, 2025
  If your Westinghouse Portable Generator's engine is running but there's no 240-Volt AC output, first check if the output indicator light is green. If so, inspect the connected electrical cords and appliances. Ensure the cord or appliance plug is fully inserted into the 240-Volt AC outlet. Try connecting a known working appliance to verify the electrical output. If the output indicator light isn't lit, and the overload alarm is red, disconnect all devices, press the reset button (iGen4500s only), and restart the engine with the ECO throttle switch OFF. Reconnect loads individually to identify any faulty or overloading devices. If the overload alarm is not illuminated, the generator may be faulty. If problems persist, take the generator to an authorized Westinghouse service dealer.
R
Richard FosterAug 28, 2025
How to fix a Westinghouse Portable Generator that runs erratically?
- L
  Luis DavisAug 29, 2025
  If your Westinghouse Portable Generator runs erratically, it could be due to varying power demands from connected devices, which is normal, especially with the ECO throttle on. If both the output indicator and overload alarm are lit, switch off or unplug devices to reduce the load. Ensure the engine is warm enough by letting it run for at least 2 minutes after moving the choke to the RUN position, and make sure the choke isn't in the START position when the engine is warm. Also, check for stale or contaminated fuel and clean the air filter if it's dirty. If the problem continues, seek assistance from an authorized Westinghouse service dealer.
J
Joseph TaylorAug 31, 2025
What to do if the electric starter on my Westinghouse Portable Generator iGen4500s won't crank?
- M
  Mercedes AndersonAug 31, 2025
  If the electric starter on your Westinghouse iGen4500s Portable Generator isn't cranking the engine properly, first disconnect any electrical devices. If the battery is flat, try starting the engine manually or recharge the battery using an external charger. If the battery is faulty, replace it. Also, ensure the remote control fob is within range and has a clear line of sight to the generator; replace the remote's battery and pair it with the generator if needed. If these steps don't resolve the issue, the generator may be faulty, and you should take it to an authorized Westinghouse service dealer.
S
Shannon PattersonSep 3, 2025
Why is there no DC output from my Westinghouse Portable Generator?
- C
  csandersSep 3, 2025
  If your Westinghouse Portable Generator is running but has no 5 or 12-Volt DC output, first check that the electrical cord or appliance plug is fully inserted into the DC outlet. If it is, test the appliance with a known working one to verify the electrical output. Also, check for any overload or short circuit in the connected DC load. Disconnect all devices, restart the engine with the ECO throttle switch OFF, and ensure the DC devices do not overload the generator's rated DC output. If problems persist, the generator may be faulty, and you should consult an authorized Westinghouse service dealer.
A
Amy ShepherdSep 6, 2025
What to do if my Westinghouse iGen4500s Portable Generator has no electrical output?
- J
  Jeffrey OneillSep 6, 2025
  If your Westinghouse Portable Generator is running but providing no electrical output, first, try resetting the reset breaker. Also, ensure the power cord plug is fully connected to the inverter's outlet. If that doesn't work, the power cord or the electrical appliance you're using might be faulty. Try replacing the power cord or connecting a known working appliance to check if the inverter is producing power.
M
Megan WhiteSep 9, 2025
Why does my Westinghouse iGen4500s Portable Generator suddenly stop?
- R
  Raymond WhiteSep 9, 2025
  If your Westinghouse Portable Generator suddenly stops running, there could be several reasons. First, check the fuel level and add fuel if necessary. Another possible cause is the low oil shut down switch, so check the oil level and add oil if needed. Finally, too much load can cause the generator to stop; in this case, restart the inverter and reduce the load.
B
Brianna SheaSep 10, 2025
How to fix a Westinghouse iGen4500s that won't start?
- J
  Jared MarquezSep 12, 2025
  If your Westinghouse Portable Generator won't start or stay running, several issues could be the cause. Start by adding gasoline to the inverter. Check and clean the air filter. Make sure to check the oil level and add oil if necessary. Ensure the spark plug boot is fully engaged with the spark plug tip. Remove and check the spark plug, replacing it if faulty. Check and clean the spark arrestor. Also, drain any stale fuel and replace it with fresh fuel. Finally, inspect and clean fuel delivery passages.
L
Larry RossSep 12, 2025
Why does my Westinghouse Portable Generator engine run erratic?
- P
  pcastroSep 12, 2025
  If the engine of your Westinghouse Portable Generator runs erratically and doesn't hold a steady RPM, first, make sure the choke is in the RUN position, not the CHOKE position. Next, clean the air filter. Also, changes in engine speed may occur as applied loads cycle; this is a normal condition.
M
Mary HowardNov 15, 2025
Why won't my Westinghouse iGen4500s Portable Generator start?
- V
  Vincent CastroNov 15, 2025
  If your Westinghouse Portable Generator's engine won't start or runs rough, several factors could be at play. First, ensure the oil level is adequate and add oil if needed. Next, check the fuel level and replenish if necessary. Stale or contaminated fuel can also cause issues, so drain and refill with fresh fuel. Disconnect any electrical loads from the 240-Volt AC receptacles. Make sure the fuel cap vent and fuel control switch are in the ON position. For iGen4500s models, the engine control switch should be in the AUTO RUN position. If the engine is cold, use the choke; if hot, adjust the choke position. Check that the spark plug boot is firmly connected, and the spark plug itself is clean. Lastly, inspect the air filter and spark arrester for blockages. If none of these steps work, cons...

Westinghouse iGen4500s Specifications

General

Starting Wattage	4500 Watts
Running Wattage	3700 Watts
Fuel Type	Gasoline
Engine Type	4-Stroke OHV
Runtime at 50% Load	18 Hours
Noise Level	52 dBA
Engine Displacement	224 cc
Fuel Tank Capacity	3.4 Gallons
Inverter	Yes
Voltage	120V
Frequency	60 Hz
Wheel Kit	Yes
Weight	98 lb
Start Type	Electric/Remote/Recoil