Whirlpool LSA 1300 - RID#2 Component Error Codes and Troubleshooting

b)
Ensure that
for
Torque Motor
c)
Check for any
d)
Ensure that drain hose free end should be left in atmosphere not in any
other medium.
e)
Check for pressure sensor frequency response.
RID#2.3 SS1 ERROR
1)
SS1 Error will be detected if there is no
Load Sensing, Indexing, SIS and Speed based spin.
2) Need to check :
a)
Run a Spin Program and check the basket is running if not check for Motor,
Capacitor, Torque motor connections (from PCB to specific loads) and its
operation.
b)
Slot sensor
entry in between slot sensor connector & its wiring harness connector.
c)
Check for Slot sensor operation.
RID#2.4 E1 ERROR
1)
If there is no feedback from pressure sensor or if the frequency is
error will be popped
2) Need to check :
a)
Check for pressure sensor operation and its Connections (from PCB to
sensor).
b)
Ensure that there is no Kink or Water entry into pressure hose.
c)
Check for Inlet valve continuous flow
d)
Ensure that PCB is
e)
For manual water fill, ensure the amount of water filled should be less than
the level of balance ring
RID# 2.5 UNBALANCE ERROR
1)
During SIS, if the system fails to attain 50 to 150 Rpm / 150 to 300 Rpm / if the Off
balance threshold value
Ub error.
2)
While detecting Ub
a)
For the Ist detection (Ub and the time will be flashed), Self correction process
will be done. i.e. Water fill and then agitation so as to distribute the cloths
CONTROL COMPONENTS
AND SPECIFICATION
Ensure that
Torque Motor
is turning ON during drain process and if not check
Torque Motor
operation & its connections from PCB to drain pump.
Check for any
kink or blockage at drain hose.
Ensure that drain hose free end should be left in atmosphere not in any
other medium.
Check for pressure sensor frequency response.
SS1 Error will be detected if there is no
feedback from slot sensor for
Load Sensing, Indexing, SIS and Speed based spin.
Run a Spin Program and check the basket is running if not check for Motor,
Capacitor, Torque motor connections (from PCB to specific loads) and its
Slot sensor
connections should be checked and also ensure there is no water
entry in between slot sensor connector & its wiring harness connector.
Check for Slot sensor operation.
If there is no feedback from pressure sensor or if the frequency is
error will be popped
Check for pressure sensor operation and its Connections (from PCB to
Ensure that there is no Kink or Water entry into pressure hose.
Check for Inlet valve continuous flow
Ensure that PCB is
working fine.
For manual water fill, ensure the amount of water filled should be less than
the level of balance ring
RID# 2.5 UNBALANCE ERROR
During SIS, if the system fails to attain 50 to 150 Rpm / 150 to 300 Rpm / if the Off
balance threshold value
gets crossed within a specified tenure then control moves to
While detecting Ub
For the Ist detection (Ub and the time will be flashed), Self correction process
will be done. i.e. Water fill and then agitation so as to distribute the cloths
AND SPECIFICATION
SERVICE MANUAL
Page | 27
is turning ON during drain process and if not check
operation & its connections from PCB to drain pump.
Ensure that drain hose free end should be left in atmosphere not in any
feedback from slot sensor for
10 secs during
Run a Spin Program and check the basket is running if not check for Motor,
Capacitor, Torque motor connections (from PCB to specific loads) and its
connections should be checked and also ensure there is no water
entry in between slot sensor connector & its wiring harness connector.
If there is no feedback from pressure sensor or if the frequency is
out of range, E1
Check for pressure sensor operation and its Connections (from PCB to
Ensure that there is no Kink or Water entry into pressure hose.
For manual water fill, ensure the amount of water filled should be less than
During SIS, if the system fails to attain 50 to 150 Rpm / 150 to 300 Rpm / if the Off
gets crossed within a specified tenure then control moves to
For the Ist detection (Ub and the time will be flashed), Self correction process
will be done. i.e. Water fill and then agitation so as to distribute the cloths