What to do if the Winterwarm Heater burner fan does not work?
If the burner fan in your Winterwarm Heater isn't working, start by checking if it's blocked. Next, inspect the wiring for any damage. If neither of these is the problem, the burner fan itself may be defective and require replacement.
What to do if my Winterwarm Heater shows E-error for more than 24 hours?
If your Winterwarm Heater displays an E-error for more than 24 hours, switch the air heater off and on and check the error code.
What to do if my Winterwarm Heater has an internal error?
To address an internal error in your Winterwarm Heater, first, isolate the electrical supply and then reenergize it. If the problem persists, replace the burner control unit.
What to do if the Winterwarm Heater has no flame after ignition?
If your Winterwarm Heater doesn't ignite, several factors could be at play. First, ensure there's sufficient gas pressure. If that's not the issue, the gas mixture might be too lean; in this case, adjust the gas valve according to section 8.1. Also, verify the gas valve is opening by checking for a 230 V voltage during ignition. Finally, check if the ignition electrode sparks. If it doesn't, inspect the cable and electrode for damage, replacing them if necessary. If the electrode sparks, the burner control unit might be faulty and need replacement.
What to do if the Winterwarm Heater flame lasts only 5 seconds after ignition?
If the flame in your Winterwarm Heater only lasts for 5 seconds after ignition, check the ignition/ionisation cable and the electrode, ensuring the cable has a resistance of 1 kΩ. Also, ensure the air heater is properly earthed. If these steps don't resolve the issue, the circuit board might be defective.
What to do if the Winterwarm Heater has too many flame failures while burning?
If your Winterwarm Heater experiences frequent flame failures during operation, it could be due to a few reasons. One possibility is an inconsistent gas supply, leading to pressure drops. Another is the burner pressure for Low fire being too low, causing the flame to extinguish prematurely. Lastly, check for recirculation of flue gas, where flue gas is drawn back into the air inlet due to a flue terminal issue, resulting in a lack of oxygen.
What to do if the Winterwarm Heater heat exchange sensor or flue sensor is overheated?
If the heat exchange sensor or flue sensor in your Winterwarm Heater is overheating, first check if the connectors J12 and J6 are correctly plugged in and if the connection J12[1-4] (optional overheating protection) is closed. Then, check if the system fan is supplying enough air. Finally, review the gas valve settings to ensure the heater isn't overfired; if it is, adjust the burner pressure.
What to do if the Winterwarm Heater pressure switch is closed in stand-by mode?
If the pressure switch in your Winterwarm Heater is closed while in stand-by mode, check if the contact is stuck and replace the pressure switch if necessary. Also, check if there is water in the hose and dry the hose if needed.
What to do if Winterwarm Heater has insufficient air passage through the heat exchanger?
If there's insufficient air passage through the heat exchanger in your Winterwarm Heater, and the pressure switch doesn't close, verify that the combustion fan is running. Also, check if the flue system is blocked or restricted. Inspect the pressure switch and its connections. Finally, check the heat exchanger for flue leakage.
What to do if the Winterwarm Heater flame detected after closing the gas valve?
If a flame is detected in your Winterwarm Heater after the gas valve closes, check if the gas valve closes too slowly and replace it if necessary. Also, check if the ionisation electrode is wet and dry, clean, or replace the electrode if needed.
Emphasizes installation by authorized personnel and compliance with regulations.
Outlines pre-installation checks including data badge verification and space requirements.
Specifies requirements for locating the heater, including clearance, distance, orientation, and suspension options.
Explains how to connect an MTS or MTC thermostat to the air heater.
Lists compatible flue terminals for vertical discharge with article numbers.
Details maximum straight flue lengths for horizontal and vertical orientations, considering bends.
Details the preparation and steps for installing a roof flue terminal.
Describes the pressure switch function for checking combustion air passage.
Outlines checks and adjustments needed for proper combustion efficiency after installation.
Guides the process of commissioning the air heater after installation.
Details how to adjust gas valve settings for high and low fire using a calibrated analyzer.
Lists volatile lock-out errors that require manual reset.
Describes temporary errors that resolve automatically once the cause is fixed.
Addresses flame detection issues lasting only 5 seconds after ignition.
Covers scenarios where no flame is detected after ignition.
Deals with overheating of heat exchange or flue sensors.
Addresses heat exchange or flue sensor not detected or short-circuit issues.
Details specific maintenance procedures for the burner unit, including electrode adjustment.
General| Brand | Winterwarm |
|---|---|
| Model | XR+ Series |
| Category | Heater |
| Language | English |
To Next Page
