Why does Wisenet Security Camera viewer get disconnected during monitoring?
Viewers might get disconnected during monitoring if there are any changes made to the camera or network configurations. To resolve this, check all network connections.
What to do if Wisenet Security Camera is not detected in Device Manager?
If your Wisenet Security Camera is not being detected in the Device Manager program, try turning off the firewall settings on your PC and then searching for the camera again.
How to fix no video on Wisenet ANO-L6022R Security Camera webviewer in Safari?
If no video is displayed when accessing the plug-in free webviewer on Safari via HTTPS: 1. On the authentication popup, click "View Authentication Certificate" and select the "Always trust when connecting to the designated webviewer IP" check box. 2. If the webviewer still fails, exit the Safari browser (command key + Q), access it again, and repeat the above steps.
Why Wisenet ANO-L6022R Security Camera cannot record into the Micro SD card?
If your Wisenet Security Camera cannot record into the Micro SD card, the memory card may be defective. When replacing the Micro SD card, make sure the power is disconnected from the product.
What to do if Wisenet ANO-L6022R does not operate properly with Micro SD card?
If your Wisenet Security Camera isn't operating correctly after inserting a Micro SD card, ensure the card is inserted in the proper direction. You can also format the Micro SD card again in the camera's menu under ; ; .
Why no video on Wisenet ANO-L6022R Security Camera webviewer or client streaming?
If no video is displayed when you newly access the webviewer or connect streaming to the client, it might be because the maximum number of profiles available is 3. The connection may be lost if you use 4 or more profiles.
How to fix Wisenet Security Camera when file is not transferred to email after motion detection?
If files are not being transferred to email after a motion detection event, verify the following settings: A. Check the settings. B. Ensure is set to . C. Confirm the option in the menu is checked.
Why Wisenet ANO-L6022R images overlap?
Images may overlap if two or more cameras are set to a single multicast address instead of different addresses. If a single address is used for multiple cameras, the images may overlap.
General| Resolution | 1920 x 1080 |
|---|---|
| Sensor Type | 1/2.8" CMOS |
| Lens Type | Fixed |
| Focal Length | 2.8 mm |
| Day/Night | Auto (ICR) |
| Video Compression | H.265, H.264, MJPEG |
| Ingress Protection | IP66 |
| Vandal Resistance | IK10 |
| IR Range | Up to 30 m |
| Material | Aluminum |
| Minimum Illumination | 0.01 Lux |
| WDR | 120dB |
| Frame Rate | 30 fps |
| Network Interface | RJ45 (10/100Mbps) |
| PoE | Yes (IEEE 802.3af) |
| Weight | 0.5 kg |
Detailed safety instructions for product installation and operation to prevent hazards and damage.
Step-by-step guide for installing the ANO series cameras, including template use and cable connection.
Step-by-step guide for installing the ANV series cameras, covering disassembly and reassembly.
Guides on connecting the camera to a local PC or network via an internet browser.
Explains how to connect the camera to a modem using DHCP and Device Manager for IP configuration.
Information on downloading and using the Device Manager software for camera setup and configuration.
Describes how to use the Device Manager to automatically find connected network cameras.
Instructions for configuring static and dynamic IP addresses for the camera.
Manual process to set a fixed IP address, subnet mask, and gateway for the camera.
Steps to obtain an IP address automatically from a DHCP server for camera network configuration.
Guide on setting up port forwarding on a broadband router to allow remote access to the camera.
Instructions for setting a secure password for the camera login, including complexity requirements.
Provides solutions for common problems encountered with video display, network access, and SD card recording.
To Next Page
