Parts 49
MAN0962 (1/9/2012)
MAIN FRAME ASSEMBLY (FRONT SECTION)
REF PART QTY DESCRIPTION
1 19160KT 1 Blade kit, CCW
2 ----- 1 Gearbox (see pages 58 - 61)
3 1004933 1 Driveline complete, 1340, 1.75-20 6.0
w/ clutch (see page 62)
4 ----- 1 Splitter gearbox (see pages 54 - 57)
5 1021103 1 CV Drive - 540 RPM (see page 65)
5 1021104 1 CV Drive - 1000 RPM (see page 65)
6 1003491 1 Attitude rod
7 1033941 2 Front skid
8 19407 1 Safety chain
9 1008190 2 1-1/2 Blade pin kit (includes 13 & 14)
10 1034258 1 Crossbar Assembly
11 10520 2 Shim, 18 GA, 1-1/2 blade pin
12 13946 2 Shim, 20 GA, 1-1/2 blade pin
13 32603 2 Keyhole plate - special
14 32604 2 Blade pin lock clip - special
15 1003495 2 Hinge pin
16 1034265 1 Splitter shield
17 1003828 1 Manual tube
18 1034269 1 Rear shield
19 1003444 1 Front drive shield
20 1034268 1 Shield standoff
21 52232 1 Parking jack
22 1033938 1 Clevis tongue (includes 23, 40, 97,
101 & 103) -or-
22 1033940 1 Swivel tongue (includes 24, 25, 26, 40,
92, 96, 97, 101 & 103) -or-
22 1033944 1 Pintle tongue (includes 26, 27, 28, 29,
92, 96, 106, 107, 110 & 112)
23 1005595 1 Hitch, Cat. 2 clevis
24 1031356 1 Tongue level bracket (optional)
25 1031360 1 Hitch, Cat 2 clevis
26 1031362 1 2.62 x 3.00 x 2.00 Sleeve
27 1031376 1 Pintle hitch (optional)
28 11267 1 Pintle ring (includes washer, nut and
cotter pin)
29 1016969 2 Pintle bushing
30 1003440 1 H-Frame
31 1033597 1 Hydraulic hose holder
32 57282 1 Front 2/3 of 3-joint drive - 540 RPM
only (see page 63)
33 1004932 1 Telescoping shaft (see page 64)
34 32347 1 3-Joint bearing housing (includes 34,
35 & 66)
35 13133 1 1-1/2 ID Ball bearing
36 12128 1 .062 x 72 mm ID Snap ring
37 58982 2 Tongue pivot pin
38 1003435 1 .66 x .88 x 4.50 Sleeve
39 1791 2 .625 x 1 x .563 HT Sleeve
40 13087 2 3/4 x 1 x 9/16 HT Sleeve
41 46605 1 Clevis pin, 1 x 2.26
REF PART QTY DESCRIPTION
60 1266 * 3/16 x 1-1/2 Cotter pin
62 1285 * 1/4 x 1-1/2 Cotter pin
63 6185 * 1/4 x 2-1/4 Cotter pin
64 66016 * Spring pin, 1/4 x 1-1/2
65 12296 * 1/4-28 Grease fitting
66 2985 * 1/4-28 x 90° Grease fitting
71 14562 * 5/16 NC x 1 HHCS GR5
72 35155 * 5/16 SAE Flat washer
73 2472 * 5/16 Lock washer
74 4529 * 5/16 NC Hex nut ZP
76 839 * 3/8 NC x 1 HHCS GR5
77 838 * 3/8 Lock washer
79 66840 3/8 NC 3-Prong knob
82 6100 * 1/2 NC x 1-1/4 HHCS GR5
84 3508 * 1/2 NC x 4-1/2 HHCS GR5
87 3598 * 1/2 Flat washer
88 11900 * 1/2 NC Flange lock nut
89 1003445 .50 x 1.00 x 1.031 Sleeve
91 902 * 5/8 NC x 2 HHCS GR5
92 300457 * 5/8 NC x 3-3/4 HHCS GR5
93 23638 5/8 NC x 7 HHCS GR5
94 10635 5/8 x 1-3/4 x 14 GA Cup washer
95 6239 * 5/8 NC Hex lock nut
96 19025 * 5/8 NC Flange lock nut
97 13759 * 3/4 NC x 2-1/4 HHCS GR5
98 30068 * 3/4 NC x 2-1/2 HHCS GR5
99 57798 3/4 Hardened flat washer
100 8424 3/4 x 2 x 3/8 Flat washer
101 28873 3/4 ID x 1-1/2 OD x 1/4 Thick washer
102 2371 * 3/4 NC Hex lock nut
103 302207 3/4 NC Flange lock nut
106 15278 1 NC x 7-1/2 HHCS GR5
107 1863 * 1" Flat washer
110 34279 1 NC Hex lock nut
111 1024670 1.22 x 2.205 x .236 Washer
112 2370 1.62 x 3 x .16 Washer
113 24801 M8 x 1.25P x 20 mm HHCS
114 307130 M8 x 1.25P x 40 mm HHCS
115 39323 M30 x 2.0P Castle nut
120 1034084 Complete decal set
121 1003679 English safety decal set
122 1036791 Spanish safety decal set
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
Rev. (9/11/2013)
To Next Page
Loading...
