❶
Use a resin that cures faster.
❷
Use a larger layer thickness to save printing time.
❸
Increase the speed of descent and the speed of lifting as appropriate.
©Why is the support broken during the printing process?
❶
The layer exposure time is not enough
,
the layer exposure time should be increased appropriately.
❷
If the support is too thin
,
a thicker support should be used.
❸
The surrounding support is not dense enough,need to add more dense support.
❹
Check the FEP lm up and down
,
whether there is any obstruction or resin residue on the LCD screen.
❺
The lifting speed is too high and damaged the support
,
the lifting speed should be reduced appropriately.
❻
The Z-axis motion is not smooth. Correct the Z-axis and add some grease.
❼
If the hardness of the resin is too low
,
a resin with a higher hardness should be used.
©Why is the cross section of the model deformed?
❶
Because the exposure time is too long or insufcient
,
the exposure time should be adjusted appropriately.
❷
The resin selected is not in the specied curing band.
❸
Some points are are not adding support and the model part is sunken and deformed.
❹
The platform handle is not tightened when printing.
❺
The tank is not installed well.
❻
Check the FEP lm up and down
,
whether there is any obstruction or resin residue on the LCD screen.
❼
If the hardness of the resin is too low
,
a resin with a higher hardness should be used.
©Why is the height of the printed model incorrect?
❶
The platform is not leveled.
❷
Z-axis stuck
,
the Z-axis should be corrected and grease added.
❸
The platform handle is not tightened when printing.
❹
The underlying exposure time is too long and the bottom layer is inated.
❺
Because the exposure time is too long or insufcient
,
the exposure time should be adjusted appropriately.
❻
Check if the UV LED on the light board is fully illuminated when printed
,
and if the brightness is different.
❼
The lifting distance is too large
,
and the position is misplaced when moving up and down for a long distance.
❽
Open the print le with
SparkStudio
and check for any problems with the sliced graphics.
©Why is a cuboid block that is the size of the screen printed on the printing platform
after printing is finished
,
or not printed anything?
❶
If the LCD screen is damaged or the contact is poor
,
it will be completely transparent. Check the LCD screen
cable and try to connect again. If it cannot be solved
,
replace the new LCD screen.
❷
Check that the lamp bead on the lamp board is lit normally when printed.
❸
Open the print le with
SparkStudio
and check for any problems with the sliced graphics.
❹
The copper nut mounting screw is too tight
,
the screw is stuck
,
and the copper nut mounting screw should be
adjusted to make the screw move smoothly.
©Why is the LCD screen not working?
❶
The resin drop into the LCD screen and damage the LCD screen.
❷
The residual resin residue on the tank or platform crushes the LCD screen during printing.
❸
The connection cable inside the LCD screen is loose during transportation.
❹
Check the FEP lm in the tank
,
and whether there is any obstruction or resin residue on the LCD screen.
©Why does the bottom of the model swell?
In order to make the model stick to the bottom layer of the platform
,
the bottom exposure time is longer than the
normal layer
,
and the long under layer exposure time will cause the resin around the bottom layer expand
,
you can
lift the model a distance and then add the bottom support.
©The aluminum plate of the printing platform has been scratched by the tool after
repeated use
,
can it be used?
Slight scratches have little effect on the model and it can be used continuously
,
and the rougher the metal
plane
,
the stronger the adhesion.
©How to improve the printing speed?
104
FAQ
105
FAQ
To Next Page
Loading...
Need help?
General