Wyrestorm EX-70-G2 - User Manual

70m/230ft 2K HDMI Extender
with IR control and CEC pass-through
EX-70-G2
Quickstart Guide
In the Box
1x EX-70-G2 Transmitter
1x EX-70-G2 Receiver
1x 18V DC 1A Power Supply (US/UK/EU)
1x Wide-band IR Emitters
1x Wide-band IR Receivers (30-50KHz)
4x Mounting Brackets (1pr for TX and 1pr for RX)
1x Quickstart Guide (this document)
Basic Wiring Diagram
HDMI Display
HDMI
HDMI
IR Emitter
IR Emitter
IR Receiver
18V DC 1A
Power Supply
IR to Control System
CAB-IR-LINK (Sold Separately)
EX-70-G2 Transmitter (TX)
EX-70-G2 Receiver (RX)
HDMI Source
KEY
HDMI
HDBaseT Cat5e/6/6a
IR TX and RX
Power
HDBaseT
Cat6/6a/7
or
IMPORTANT!
Disconnecting and connecting (hot plugging) HDMI, or HDBaseT while
devices are powered on may cause damage. WyreStorm recommends
powering off devices before disconnecting these connections.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of this
product. Refer to the Installation Guide and other documentation on the
product page for additional information.
Installation
Before Beginning
• Verify that all items are included in the packaging per the In the Box list.
Pre Wire
1. Run a Cat5e/6/6a cable from the transmitter location to the receiver
location. Terminate the cable per the HDMI/HDBaseT Wiring section.
2. (Optional) If using 3rd party IR emitters or connecting blocks at either
the transmitter or receiver, run the wire and terminate per the IR TX
(Emitter) Wiring section.
3. (Optional) If using 3rd party IR receivers at either the transmitter or
receiver, run the wire and terminate per the IR RX (Receiver) Wiring
section.
Transmitter Installation
1. Connect an HDMI source to the HDMI In on the transmitter using an
HDMI cable from a high quality brand such as WyreStorm Express.
2. (Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the IR TX port.
3. Connect the cable created in Pre Wire step 1 to the HDBT Out.
4. If using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the 18V DC 1A jack.
Receiver Installation
1. Connect the HDMI Out on the receiver to an input on the display using
an HDMI cable from a high quality brand such as WyreStorm Express.
2. (Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the IR TX port.
3. Connect the cable created in Pre Wire step 1 to the HDBT In.
4. If not using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the 18V DC 1A jack.
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
EX-70-G2 Quickstart Guide | 170724
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.

Wyrestorm EX-70-G2 Specifications

Audio and Video

audio formats	2ch PCM | Multi Channel up to Dolby Atmos and DTS-X
hdmi resolutions	1920x1080p @60Hz 12bit, 16bit; 3840x2160p @30Hz 4:4:4 8bit; 3840x2160p @60Hz 4:2:0 8bit; 4096x2160p @60Hz 4:2:0 8bit
cat6 resolutions	1920x1080p @60Hz 8bit, 12bit (60m/197ft); 3840x2160p @30Hz 4:4:4 8bit (35m/115ft); 4096x2160p @60Hz 4:2:0 8bit (35m/115ft)
cat6a/7 resolutions	1920x1080p @60Hz 8bit, 12bit (70m/230ft); 3840x2160p @30Hz 4:4:4 8bit (40m/131ft); 4096x2160p @60Hz 4:2:0 8bit (40m/131ft)
color depth	1080p: 16bit | 4K UHD: 8bit

Communication and Control

hdmi	HDMI 2.0 | HDCP 1.4 | EDID pass-through | CEC Pass-through | DVI/D supported with adapter
hdbaset	HDMI 2.0 | HDCP 1.4 | EDID pass-through | 2-way PoH | Bidirectional IR and RS-232
ir	1x IR TX 3.5mm Mono | Bidirectional over HDBaseT | 1x IR RX 3.5mm Stereo | Bidirectional over HDBaseT

Power

input voltage	100~240V AC 50/60Hz
output voltage	18V DC 1A
max power consumption	8.88W
poh	19V Non-Standard 13W

Environmental

operating temperature	32°F ~ 113°F (0°C ~ 45°C)
storage temperature	-4°F ~ 158°F (-20°C ~ 70°C)
humidity	10% ~ 90%, non-condensing
maximum btu	30.30 BTU/hr

Weight and Dimensions

rack units/wall box	0.3U
height	15mm/0.6in
width	109mm/4.3in
depth	64mm/2.5in
weight (each unit)	0.36kg/0.79lbs

Summary

Installation Guide

Before Beginning Installation

Verify all items are included in the packaging before starting the installation process.

Pre Wire Installation Steps

Run Cat5e/6/6a cable from transmitter to receiver location and terminate per wiring sections.

Transmitter Installation Procedure

Connect HDMI source to transmitter and HDBT Out to receiver, including power connection.

Receiver Installation Procedure

Connect HDMI Out to display and HDBT In to transmitter, including power connection if needed.

Device Component Identification

Front Panel Overview

Details of front panel LEDs (Power, Status, HDCP, Link) for both TX and RX units.

Rear Panel Connection Ports

Identifies rear panel ports including Power In, HDBT, IR TX/RX, and HDMI.

Wiring and Connectivity

HDMI and HDBaseT Wiring Guidelines

Provides HDBaseT wiring standards (T568B) and cable performance guidelines.

IR Emitter and Receiver Wiring

Details connections for IR TX (mono) and IR RX (stereo) 3.5mm jacks.

Power Supply and PoH

Explains power delivery via transmitter (PoH) or separate 18V DC 1A supply.

Specifications and Troubleshooting

Product Specifications

Lists technical details including inputs, outputs, resolutions, dimensions, and environmental factors.

Troubleshooting Common Issues

Provides solutions for no/poor picture quality and intermittent 3rd party device control.