To Next PageTo Next Page
Need help?Do you have a question about the Yaesu FT-950 - MENU MODE LIST and is the answer not in the manual?
General| Voltage | 13.8 V DC ±15% |
|---|---|
| Frequency Coverage | 30 kHz - 56 MHz |
| Mode | USB, LSB, CW, AM, FM, FSK |
| RF Power Output | 100 W (25 W AM carrier) |
| Memory Channels | 99 |
| Current Consumption | 22 A (max) |
| Operating Temperature | -10 °C to +50 °C |
Sets the delay time for the AGC FAST mode.
Sets the delay time for the AGC MID mode.
Sets the delay time for the AGC SLOW mode.
Selects display color when optional DMU-2000 is connected.
Sets the display brightness level for the VFD.
Selects parameter viewed on Tuning Offset Indicator.
Selects peak hold time for the S-meter.
Selects peak hold time for the PO meter.
Selects peak hold time for the ALC meter.
Selects peak hold time for the ID meter.
Selects the starting point for the rotator controller's indicator needle.
Adjusts the rotator indicator needle precisely to the set starting point.
Enables/disables QMB Marker display on Spectrum Band Scope.
Sets the audio output level from the optional DVS-6 Voice Memory Unit.
Sets the microphone input level to the optional DVS-6 Voice Memory Unit.
Sets the interval time between repeats of the beacon message.
Selects the Contest Number "Cut" format for an imbedded contest number.
Enters the initial contest number that will increment/decrement during contest QSOs.
Permits entry of the CW message for message register 1.
Permits entry of the CW message for message register 2.
Permits entry of the CW message for message register 3.
Permits entry of the CW message for message register 4.
Permits entry of the CW message for message register 5.
Sets the method of antenna selection.
Sets the beep level.
Sets the transceiver's computer-interface circuitry for CAT baud rate.
Sets Time-Out Timer countdown for CAT command input.
Enables/Disables the RTS port of the CAT jack.
Enables/Disables Memory Group Operation.
Selects tuning offset for the Quick Split feature.
Sets the Time-Out Timer countdown time for transmitter.
Selects the µ-TUNE mode.
Enables/disables scanning access via microphone UP/DWN keys.
Selects the Scan Resume mode.
Adjusts the reference oscillator.
Sets the microphone gain for the AM mode.
Selects keyer operation mode for front panel KEY jack.
Selects keyer paddle wiring configuration for front panel KEY jack.
Selects keyer operation mode for rear panel KEY jack.
Selects keyer paddle wiring configuration for rear panel KEY jack.
Enables/disables CW keying while operating on SSB.
Sets the CW carrier oscillator injection side for CW mode.
Sets the CW "break-in" mode.
Adjusts the Keying Delay (receiver recovery) time on CW mode.
Adjusts your preferred CW tone pitch.
Sets the Dot:Dash ratio for the built-in electronic keyer.
Selects the frequency Display Format for the CW mode.
Enables/disables CW keying from the DATA PTT terminal.
Selects time delay between PTT keyed and carrier transmit during QSK.
Sets data input level from TNC to AFSK modulator.
Sets AFSK data output level at the output port of the RTTY/PKT jack.
Adjusts the "VOX" Delay (receiver recovery) time in PACKET mode.
Adjusts the "VOX" Gain in the PACKET mode.
Sets the packet frequency display offset.
Sets the carrier point during SSB packet operation.
Sets the microphone gain for the FM mode.
Sets the magnitude of the repeater shift on the 28 MHz band.
Sets the magnitude of the repeater shift on the 50 MHz band.
Selects normal or reverse Mark/Space polarity for RTTY receive.
Selects normal or reverse Mark/Space polarity for RTTY transmit.
Sets the RTTY (AFSK) data output level at the output port.
Selects the frequency shift for RTTY (AFSK) operation.
Selects the Mark tone for RTTY operation.
Selects the audio passband of the DSP modulator on SSB mode.
Adjusts the receiver carrier point for the LSB mode.
Adjusts the receiver carrier point for the USB mode.
Adjusts noise blanking level of IF Noise Blanker for short duration pulse noise.
Adjusts noise blanking level of IF Noise Blanker for longer duration pulse noise.
Adjusts the parametric equalizer gain of the Contour filter.
Adjusts the Q-factor of the Contour filter.
Enables/disables the Digital Notch Filter.
Sets the Digital Noise Reduction response.
Selects scan start frequency of FIX mode Spectrum Scope on 160m band.
Selects scan start frequency of FIX mode Spectrum Scope on 80m band.
Selects scan start frequency of FIX mode Spectrum Scope on 60m band.
Selects scan start frequency of FIX mode Spectrum Scope on 40m band.
Selects scan start frequency of FIX mode Spectrum Scope on 30m band.
Selects scan start frequency of FIX mode Spectrum Scope on 20m band.
Selects scan start frequency of FIX mode Spectrum Scope on 17m band.
Selects scan start frequency of FIX mode Spectrum Scope on 15m band.
Selects scan start frequency of FIX mode Spectrum Scope on 12m band.
Selects scan start frequency of FIX mode Spectrum Scope on 10m band.
Selects scan start frequency of FIX mode Spectrum Scope on 6m band.
Sets tuning speed of Main Tuning Dial and CLAR/VFO-B knob.
Enables/disables the "Fine" tuning speed in the CW mode.
Selects tuning steps for CLAR/VFO-B knob when MHz button is pressed.
Selects tuning steps for microphone UP/DWN keys in AM mode.
Selects tuning steps for microphone UP/DWN keys in FM mode.
Sets tuning speed of Main Tuning Dial and CLAR/VFO-B knob in FM mode.
Programs a band to be skipped while selecting bands using CLAR/VFO-B knob.
Selects center frequency of low range for parametric microphone equalizer.
Adjusts equalizer gain of the low range of the parametric microphone equalizer.
Adjusts the Q-factor of the low range of the parametric microphone equalizer.
Selects center frequency of middle range for parametric microphone equalizer.
Adjusts equalizer gain of the middle range of the parametric microphone equalizer.
Adjusts the Q-factor of the middle range of the parametric microphone equalizer.
Selects center frequency of high range for parametric microphone equalizer.
Adjusts equalizer gain of the high range of the parametric microphone equalizer.
Adjusts the Q-factor of the high range of the parametric microphone equalizer.
Selects center frequency of lower range for parametric equalizer when speech processor activated.
Adjusts equalizer gain of the low range for parametric equalizer when speech processor activated.
Adjusts Q-factor of the low range for parametric equalizer when speech processor activated.
Selects center frequency of middle range for parametric equalizer when speech processor activated.
Adjusts equalizer gain of the middle range for parametric equalizer when speech processor activated.
Adjusts Q-factor of the middle range for parametric equalizer when speech processor activated.
Selects center frequency of high range for parametric equalizer when speech processor activated.
Adjusts equalizer gain of the high range for parametric equalizer when speech processor activated.
Adjusts Q-factor of the high range for parametric equalizer when speech processor activated.
Sets a compression level of the Speech Processor.
Enable/disable the optional FC-40 Antenna Tuner.
Sets a transmitter output level.
Sets a carrier power output level.
Controls how menu item "111 TGEN TX PWR" affects modes.
Selects audio input source for triggering TX during VOX operation.
Adjusts the "VOX" Gain on the SSB/AM/FM modes.
Adjusts the "VOX" Delay (receiver recovery) time on SSB/AM/FM modes.
Adjusts Anti-VOX Trip Gain to prevent receiver audio activating transmitter.
Enables Tx/Rx operation on the Alaska Emergency Channel, 5167.5 kHz.
