16
Alignment
High TX Power Adjustment (HI POWER)
m Transmit, and adjust the output power level for 5.0 W
(±0.3 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
L3 Tx Power Adjustment (L3 POWER)
m Transmit, and adjust the output power level for 2.5 W
(±0.2 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
L2 Tx Power Adjustment (L2 POWER)
m Transmit, and adjust the output power level for 1.0 W
(±0.1 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
L1 Tx Power Adjustment (L1 POWER)
m Transmit, and adjust the output power level for 50 mW
(+50/-30 mW) by rotating the DIAL, then press the V/M
button. Rotate the DIAL to select the next setting.
TX Deviation Adjustment (MAX DEV)
m Inject a 1 kHz audio tone at a level of 50mV (rms) to
the MIC jack. Press the V/M button, then transmit and
adjust the deviation for 4.5 kHz (±0.2 kHz) (USA Ver-
sion: 4.2 kHz (±0.2 kHz)) by rotating the DIAL, then
press the V/M button. Rotate the DIAL to select the next
setting.
CTCSS Tx Deviation Adjustment (TN 67.0)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (+0.05/-0.1 kHz) by rotating the
DIAL, then press the V/M button. Rotate the DIAL to
select the next setting.
CTCSS Tx Deviation Adjustment (TN 183.5)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
CTCSS Tx Deviation Adjustment (TN 254.1)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
DCS Tx Deviation Adjustment (DCS DEV)
m Press the V/M button, then transmit and adjust the de-
viation for 0.6 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
Press the MON/F to activate the TX Power and Devia-
tion alignment routine.
The alignment frequency will automatically be set to
146.000 MHz (USA Version: 148.000 MHz).
High TX Power Adjustment (HI POWER)
m Transmit, and adjust the output power level for 5.0 W
(±0.3 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
High TX Power Adjustment (L3 POWER)
m Transmit, and adjust the output power level for 2.5 W
(±0.2 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
High TX Power Adjustment (L2 POWER)
m Transmit, and adjust the output power level for 1.0 W
(±0.1 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
High TX Power Adjustment (L1 POWER)
m Transmit, and adjust the output power level for 50 mW
(+50/-30 mW) by rotating the DIAL, then press the V/M
button. Rotate the DIAL to select the next setting.
TX Deviation Adjustment (MAX DEV)
m Inject a 1 kHz audio tone at a level of 50mV (rms) to
the MIC jack. Press the V/M button, then transmit and
adjust the deviation for 4.5 kHz (±0.2 kHz) (USA Ver-
sion: 4.2 kHz (±0.2 kHz)) by rotating the DIAL, then
press the V/M button. Rotate the DIAL to select the next
setting.
CTCSS Tx Deviation Adjustment (TN 67.0)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (+0.05/-0.1 kHz) by rotating the
DIAL, then press the V/M button. Rotate the DIAL to
select the next setting.
CTCSS Tx Deviation Adjustment (TN 183.5)
m Press the V/M button, then transmit and adjust the de-
viation for for 0.5 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
CTCSS Tx Deviation Adjustment (TN 254.1)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
To Next Page
Loading...
