Yamaha EMX5016CF Service Manual (English)

Other manuals for Yamaha EMX5016CF

Service Manual38 pages

Manual16 pages

Brochure & Specs6 pages

Questions and Answers:

A
Anthony MatthewsAug 15, 2025
How to fix Yamaha Music Mixer sound that is faint, distorted, or noisy?
- A
  Angela JacksonAug 15, 2025
  Check if the GAIN controls, channel faders, ST master fader, and AUX1/2 faders are set to the correct levels. Also, verify that the [26 dB] switches on channels 1 to 8 are correctly set. Ensure that you haven't connected to both INPUT A and INPUT B on channels 1 to 8 simultaneously. Confirm that the input signal from the connected device is at an appropriate level and reduce excessive digital effect.
B
brittney73Aug 19, 2025
How do I initialize the GEQ and digital effect settings on my Yamaha Music Mixer?
- C
  Crystal JacksonAug 19, 2025
  To restore the initial factory settings for GEQ, Effects, Feedback Suppressor, and MAXIMIZE, turn on the power while holding the GEQ ON switch and MAXIMIZE ON switch.
L
Lindsey MorrisAug 21, 2025
Why is no effect applied on my Yamaha Music Mixer?
- L
  Lisa ConnerAug 21, 2025
  Check that the EFF1/2 knob on each channel is correctly adjusted. Be sure that the internal effector’s ON switch is turned on. Check that the EFF1/2 RTN fader is correctly adjusted.
J
Jenny BernardAug 25, 2025
What to do if there is no sound from my Yamaha Music Mixer?
- L
  Lance RobertsAug 25, 2025
  First, ensure that all microphones, external devices, and speakers are correctly connected. Then, check if the GAIN controls, channel faders, ST master fader, and AUX1/2 faders are set to appropriate levels. Also, make sure the speaker cables are not shorted. If the problem persists after these checks, further assistance may be needed.
R
Rhonda VasquezAug 27, 2025
Why won't my Yamaha Music Mixer power on?
- J
  jeffersonsamuelAug 27, 2025
  Make sure you are using the power cord supplied with the unit. Verify that it is correctly connected to the AC IN connector and plugged into a working power outlet.
D
dpearsonAug 30, 2025
What to do if the sound suddenly stopped on my Yamaha Music Mixer?
- W
  wadejulianAug 30, 2025
  The unit may be overheating. Check whether the vents at the front and rear of the unit are blocked. If they are, wait for it to cool down, and then turn the power back on.
M
Michael KrauseSep 2, 2025
What to do if my Yamaha Music Mixer power suddenly went off?
- T
  Tricia GibsonSep 3, 2025
  The EMX unit may overheat if the vents are blocked. Check whether the vents at the front and rear of the unit are blocked. Wait for the unit to cool down, and then turn the power back on.
L
Lauren HopkinsSep 5, 2025
How do I get a more forceful sound from the speakers on my Yamaha Music Mixer?
- K
  kelsey30Sep 6, 2025
  Try turning on the YS Processing switch. Also, try turning on the MAXIMIZE ON switch. Adjust the equalizers (HIGH, MID, and LOW knobs) on each channel and adjust the graphic equalizers.
B
Brian WilsonSep 8, 2025
How to output a monitor signal through speakers using Yamaha Music Mixer?
- H
  Haley SantosSep 9, 2025
  Connect a powered speaker to the AUX1/2 jacks. Then adjust the AUX1/2 signal by adjusting the channel AUX1/2 controls and the AUX1 and AUX2 faders. If you want to send the monitor signal to SPEAKERS A jack, set the POWER AMP switch to the AUX1/MONO position.
S
shawnperkinsSep 12, 2025
How can I make spoken words be heard more clearly using my Yamaha Music Mixer?
- B
  Bianca WilsonSep 12, 2025
  Ensure that the switches (high pass filters) for the relevant channels are turned ON as appropriate. Make sure that the YS Processing switch is turned off. Adjust the equalizers (HIGH, MID, and LOW knobs) on each channel and adjust the graphic equalizers.

Yamaha EMX5016CF Specifications

General

Channels quantity	16 channels
Digital sound processing	- bit
Phantom power	48 V
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Power consumption (typical)	500 W
DJ mixer	-
Product color	Black
Video capability	No
Equalizer bands quantity	9
Total Harmonic Distortion (THD)	0.3 %