Need help?Do you have a question about the Yamaha HTR-4064 and is the answer not in the manual?
General| Type | AV Receiver |
|---|---|
| Channels | 5.1 |
| Power Output (per channel) | 100W (6 ohms, 1 kHz, 0.9% THD, 1 ch driven) |
| Frequency Response | 10 Hz - 100 kHz |
| Input Impedance | 47 kΩ |
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Signal-to-Noise Ratio | 100 dB |
| Surround Sound | Yes |
| USB Port | Yes |
| Bluetooth | No |
| Dimensions (W x H x D) | 435 x 151 x 315 mm |
| Audio decoding | Dolby TrueHD, DTS-HD Master Audio |
| Input Sensitivity | 200 mV |
Accessories supplied with the AV receiver unit.
For connecting the supplied YPAO microphone.
Protects the VIDEO AUX jack from dust.
For connecting the AM antenna.
For connecting the FM antenna.
Contains the owner's manual for the unit.
Provides general setup procedures for the unit.
Provides important safety instructions.
Insert the two supplied AAA batteries into the battery case correctly.
Aim the remote control within the specified range at the sensor.
Overview of the AV receiver's capabilities and features.
Connect external devices like BD/DVD players and CD players.
Create immersive surround sound fields.
Tune into FM/AM stations and register favorites.
Enjoy original sound quality with minimal circuitry.
Operate the unit using the TV monitor for menus.
Solutions for common operational challenges and questions.
Description of controls and indicators on the front panel.
Turns the unit on or into standby mode.
Indicates standby mode status for various conditions.
For connecting the supplied YPAO microphone.
Receives signals from the remote control.
Changes displayed information on the front display.
Registers FM/AM stations as preset stations.
Selects FM/AM preset stations.
Switches FM/AM tuner band.
Changes FM/AM tuner frequency.
Enables/disables direct mode.
For connecting headphones.
For connecting USB devices.
Switches the selected input source.
Adjusts high/low frequency output.
Selects input source and sound program with one button.
Selects sound program and surround decoder.
Enables/disables straight decoding mode.
For connecting camcorders, game consoles, etc.
Adjusts the volume level.
Lights up when an HDMI device is connected or signal is output.
Lights up when CINEMA DSP sound program is activated.
Lights up when CINEMA DSP 3D is activated.
Lights up when Compressed Music Enhancer is active.
Lights up when Adaptive DRC is activated.
Lights up when stereo broadcasting is input.
Lights up when the sleep timer is on.
Flashes when audio is muted.
Displays the current volume level.
Lights up available cursors on the remote control.
Displays a range of information about the unit.
Displays speaker terminals outputting signals.
For connecting optional Yamaha iPod universal dock or wireless system.
For outputting audio/video signals to a TV.
For connecting AM and FM antennas.
For connecting external HDMI compatible devices.
For connecting speakers.
For connecting the unit to an AC wall outlet.
For outputting video signals to a TV.
For connecting playback devices with audio/video outputs.
For outputting received audio/video signals.
For connecting playback devices with analog audio outputs.
For connecting a subwoofer.
Transmits infrared signals for remote operation.
Switches an external device on and off.
Select an input source on the unit to play back.
Operate the FM/AM tuner.
Switches information displayed on the front display.
Sets the sleep timer.
Selects input source and sound program with one button.
Displays/finishes the Setup menu.
Cursor keys, ENTER, RETURN for menu navigation.
Operate recording, playback, menu displays for external devices.
Switches FM broadcast receiving or iPod operation modes.
Enter numbers for frequency or remote control codes.
Control TV operation like input and volume.
Sets remote control codes for external devices.
Switches control between unit and external device.
Switches sound field effect and surround decoder.
Adjusts volume balance.
Turns mute function on and off.
Perform the following 8 steps before using the unit for the first time.
Refer to 'Ideal speaker layout' for guidance.
Illustration of speaker placement for a 5.1-channel system.
Illustration of speaker placement for a 4.1-channel system.
Illustration of speaker placement for a 3.1-channel system.
Illustration of speaker placement for a 2.1-channel system.
Example connections for a 5.1-channel speaker setup.
Connect speaker wires to the unit's terminals.
Use a monaural pin cable to connect a subwoofer.
Details on HDMI, Component, and Video jacks.
Details on Optical, Coaxial, Audio, and Portable jacks.
Connect a TV to the unit using an HDMI cable.
Ensure the TV's ARC function is set to on.
Activate HDMI Control on the unit, TV, and connected devices.
Connect a TV using an HDMI and an optical cable.
Connect a TV to the unit with an HDMI cable and an optical cable.
Connect TV to MONITOR OUT using analog video jacks.
Connect video devices like BD/DVD players to the unit.
Connect video devices using video pin and audio cables.
Match unit input jacks to video device output jacks.
Connect audio devices like CD players to the unit.
Temporarily connect devices like video cameras and game consoles.
Connect the supplied FM and AM antennas to the unit.
Use AV OUT jacks to output analog audio/video signals for recording.
Plug the power cable into the unit and an AC wall outlet.
Steps to prepare before starting the YPAO measurement process.
Follow steps to start the automatic speaker measurement.
Review the results of the YPAO speaker measurement.
Steps to follow when an error message is displayed during YPAO.
Troubleshoot warning messages that may appear after measurement.
Steps for turning on devices and selecting sources for playback.
Select and register settings for the SCENE function.
Select sound programs suitable for video content.
Select sound programs for music sources like CDs.
Select a surround decoder for multi-channel playback.
Enable/disable straight decoding mode for pure audio.
Enable/disable direct mode for noise reduction.
Enable/disable Compressed Music Enhancer.
Programs for movies, TV, and video games.
Simulates various concert hall acoustics for music.
Simulates live venues for a realistic sound experience.
Programs for stereo playback and mixing.
Creates virtual surround sound fields using DSP 3D technology.
Creates virtual surround sound without actual surround speakers.
Select a surround decoder for multi-channel playback.
Enable/disable straight decoding mode for pure audio.
Enable/disable direct mode for noise reduction.
Enhances compressed audio by adding depth and width.
Enjoy surround sound with headphones.
Select a frequency or a registered station for radio tuning.
Automatically register FM stations with strong signals.
Manually select stations and register them to preset numbers.
Choose and listen to stations registered to preset numbers.
View RDS data like Program Service, Program Type, Radio Text, Clock Time.
Automatically search for and receive traffic information broadcasts.
Listen to radio while outputting video from an external device.
Connect iPod to the unit using USB cable, dock, or wireless system.
Connect iPod wirelessly to the unit using the optional Yamaha iPod wireless system.
Select USB or DOCK as the input source for iPod control via TV.
Navigate iPod content lists and select playback options.
View song information, album art, and playback controls.
Set iPod or USB device for random order or repeated playback.
Operate iPod directly to play contents without TV display.
Connect the Bluetooth receiver to the DOCK jack.
Pair Bluetooth devices with the wireless audio receiver.
Perform wireless connection and playback songs via Bluetooth device.
Connect the USB storage device to the USB port on the front panel.
Set USB device for repeated or random playback.
Listen to USB audio while outputting video from an external device.
List of configurable settings for each input source in the Option menu.
Change unit settings using the Setup menu displayed on the TV screen.
Configure speaker size, phase, distance, and level.
Adjust Lipsync, Dynamic Range, Max Volume, and Initial Volume.
Configure CINEMA DSP 3D, Program, and Decoder.
Set Input Rename, Auto Power Down, Dimmer, Short Message, Memory Guard.
Configure HDMI Control, TV Audio Input, ARC, Standby Sync, SCENE, Audio Output, Standby Through.
Select the display language for menus and messages.
Adjust speaker size, phase, distance, and level settings.
Adjust speaker timing for simultaneous sound arrival.
Adjust the volume level of each speaker.
Adjust sound quality manually using graphic EQ.
Turns the test tone generator on or off for speaker adjustment.
Adjust audio delay to synchronize with video output.
Adjust dynamic range for audio bit streams.
Set the maximum adjustable volume level.
Set the initial volume when the unit turns on.
Turn CINEMA DSP 3D mode on or off.
Automatically bypasses DSP and tone control for analog sources.
Adjust center and surround channel volumes.
Programs for classical, live/club music.
Programs for movies, action games, and sci-fi.
Select and adjust surround decoders like PLII Music.
Change the input name displayed on the front display and TV screen.
Automatically puts the unit into standby mode after inactivity.
Adjusts the brightness of the front display.
Turns the short message display on or off.
Prohibits setting changes to prevent accidental modifications.
Enable or disable the HDMI Control function for integrated operation.
Select TV audio input source when HDMI Control is on.
Enable or disable the Audio Return Channel function.
Turn off unit automatically when TV turns off via HDMI.
Synchronize external device operation with SCENE selection.
Specify whether audio signals are output through the unit.
Specify whether audio signals are output through the TV.
Transmit HDMI signals to TV when unit is in standby mode.
Select the display language for menus and messages.
Configure system settings using the front display.
Set unit impedance based on connected speaker impedance.
Set a unique remote control ID for each receiver when using multiple units.
Match TV color encoding format (PAL or NTSC) to the connected TV.
Reset unit settings to default factory settings or specific parameters.
Register TV remote control codes to control the TV with the unit's remote.
Operate the TV using registered remote control codes.
Register codes for external devices to control them via the unit's remote.
Control external devices using assigned input selection keys.
Reset all remote control codes to initial factory settings.
Answers to common questions about unit operation and features.
Troubleshoot issues related to power and system operation.
Troubleshoot common audio playback problems like no sound or low volume.
Troubleshoot issues where sound is only output from one speaker.
Troubleshoot issues where no sound is heard from the subwoofer.
Troubleshoot no sound issues when using an HDMI cable.
Troubleshoot TV sound not outputting from the unit.
Troubleshoot issues where only front speakers output sound.
Troubleshoot noise, hum, distortion, or intermittent sound.
Troubleshoot problems where no picture is displayed.
Troubleshoot no picture issues from HDMI-connected devices.
Troubleshoot noisy FM/AM reception and station selection.
Troubleshoot problems with the remote control's operation or range.
Troubleshoot issues controlling external devices with the remote.
Troubleshoot unit access errors for USB storage or iPod.
Troubleshoot speaker wire short circuit protection activation.
Troubleshoot connection errors with iPod.
Understand loading messages for large data devices.
Troubleshoot when no playable data is found on USB/iPod.
Troubleshoot 'No device' errors for USB storage or iPod.
Troubleshoot Bluetooth device not found errors.
Troubleshoot compatibility issues with unsupported iPod models.
Troubleshoot playback issues due to selected song or data damage.
Troubleshoot display issues on the front panel.
Recommended layout for placing speakers for optimal sound.
Definitions and explanations of audio technologies and formats.
Definitions and explanations of video signals and technologies.
Diagram illustrating the path of video signals through the unit.
Details on enabling and operating the HDMI Control function.
Information on supported HDMI audio and video signal formats.
Technical specifications for the unit's input jacks.
Technical specifications for the unit's output jacks.
Technical specifications for HDMI input, output, and formats.
Technical specifications for FM/AM tuner.
Specifications for rated output power per channel.
Specifications for dynamic power output.
Specifications for bass and treble control.
Specifications for crossover filter characteristics.
Specifications for FM tuner sensitivity and performance.
Specifications for AM tuner sensitivity and performance.
Essential safety precautions for operating the unit.
Warning against modifying the unit to comply with FCC requirements.
Warning to use only supplied or high-quality shielded cables.
Information on potential interference and measures to reduce it.
Assure finest performance by reading the manual.
Warning against exposing the unit to rain or moisture.
Precautions for using the remote control and handling batteries.
Conditions for obtaining guarantee service for Yamaha products.
Instructions for proper disposal of used electrical products and batteries.
List of supplied accessories with the AV receiver.
List of required cables for connecting the unit.
Illustration of ideal speaker placement for a 5.1-channel system.
Connect speaker wires to the unit's terminals.
Connect banana plugs to the speaker terminals (except U.K./Europe).
Connect BD/DVD player, TV, and power cable to the unit.
Steps to prepare before starting the YPAO measurement process.
Troubleshoot W-1 Out of Phase warning by checking speaker cable connections.
Steps to play back a BD/DVD disc for surround sound effects.
List of remote control codes for TV brands.
List of remote control codes for VCR brands.
List of remote control codes for DVD Recorder brands.
List of remote control codes for TV cable box brands.
List of remote control codes for DVR brands.
List of remote control codes for DVD Recorder brands.
List of remote control codes for Blu-ray Disc players.
List of remote control codes for Satellite receiver brands.
List of remote control codes for Satellite receiver brands.
List of remote control codes for Satellite receiver brands.
List of remote control codes for MD players.
List of remote control codes for Tape decks.
List of remote control codes for Tuner devices.
List of remote control codes for XM Satellite Radio.
List of remote control codes for SIRIUS Satellite Radio.
List of remote control codes for iPod Dock devices.
List of remote control codes for Network devices.
List of remote control codes for LD players.
List of remote control codes for Amplifier brands.
List of remote control codes for Apple TV.
To Next Page
