PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Mixing Mode
Mixing Play
[F1] VOL/PAN
[F2] VOICE
[F3] EF SEND
[F4] TEMPLATE
[F5] VCE ED
[F6] EFFECT
Mixing Edit
Common Edit
[F1] GENERAL
[F2] MFX
[F3] MEQ
[F4] USB I/O
[F5] A/D IN
[F6] EFFECT
Part Edit
[F1] VOICE
[F2] OUTPUT
[F3] EQ
[F4] TONE
[F5] RCV SW
Mixing Job
[F1] INIT
[F2] RECALL
[F3] COPY
[F4] BULK
Mixing Voice Edit
Common Edit
[F1] GENERAL
[F2] OUTPUT
[F4] CTL SET
[F5] LFO
[F6] EFFECT
Element Edit
[F1] OSC
[F2] PITCH
[F3] FILTER
[F4] AMP
[F5] LFO
[F6] EQ
Mixing Voice Job
[F2] RECALL
[F3] COPY
[F5] DELETE
Supplementary Information
117
Part Edit
Determines the Voice for each Part. This display shows only four Parts at a time (Part 1 – 4, Part 5 – 8, Part 9 – 12, or Part
13 – 16). To switch the editable Parts, press the Cursor [<]/[>] buttons. The editable Parts can be also switched by
pressing the corresponding buttons to other Parts of numbers [1] – [16] after pressing the [TRACK] button.
[SF1] VOICE
Determines the Voice for each Part.
Bank
Determines the Voice Bank for each Part. For information about settings other than those of the Mixing Voices, see page
7.
Number
Determines the Voice Program number for each Part.
P.WithVce (Parameter with Voice)
Determines whether or not the following parameter settings of the selected Voice are copied from the Voice to the
current Part when you change a Voice for the current Part individually.
• Arpeggio settings
• Filter Cutoff Frequency
• Filter Resonance
• Amplitude EG
•Filter EG
• Pitch Bend Range (Upper/Lower)
• Note Shift
NOTE
When a Normal Voice is assigned to the Part, the following settings are always copied to the Part regardless of the “P.WithVce”
setting. On the other hand, when a Drum Voice is assigned to the part, the following settings are not copied to the part
regardless of the “P.WithVce” setting.
• “Mono/Poly”
• “Switch” (Portamento Part Switch)
• “Time” (Portamento Time)
• “Mode” (Portamento Mode)
Settings: off (not copied), on (copied)
[SF2] MODE
Mono/Poly
Selects monophonic or polyphonic playback for each Part. Monophonic is for single notes only, while polyphonic is for
playing multiple simultaneous notes.
Settings: mono, poly
NOTE This parameter is not available for the Parts to which Drum Voices have been assigned.
ReceiveCh (Receive Channel)
Determines the MIDI receive channel for the selected Part. Since MIDI data may be coming from many channels at
once, you should set this to match the particular channel over which the desired controlling data is being sent.
Settings: 1 – 16, off
ArpPlyOnly (Arpeggio Play Only)
Determines whether or not the current Part plays only the note events of Arpeggio playback. When this parameter is set
to on, only the note events of Arpeggio playback affect the tone generator block.
Settings: off, on
Operation
[SONG]/[PATTERN] Song/Pattern selection [MIXING] [EDIT] Number [1] – [16]
[F1] VOICE
To Next Page
Loading...
Need help?
General
Weight and Dimensions
