Why is there a lack of bass and no ambience on my Yamaha R-S201?
If there is a lack of bass and no ambience with your Yamaha Receiver, ensure the + and – wires are connected in the correct phase at both the amplifier and the speakers.
What to do if the sound suddenly goes off on my Yamaha R-S201 Receiver?
If the sound from your Yamaha Receiver suddenly goes off, it may be due to the protection circuitry being activated by a short circuit. Check that the speaker wires are not touching each other and then turn the power of this unit back on. Also, ensure the openings on the top panel are not blocked, as overheating can cause this issue. Finally, review the AUTO POWER STANDBY setting in the Option menu, as it may be set to standby mode.
What to do if my Yamaha R-S201 remote control is not working?
If the remote control for your Yamaha Receiver isn't working correctly: 1. Ensure you are within 6 meters (20 ft) and within 30 degrees of the front panel. 2. Reposition the unit if direct sunlight or lighting is interfering with the remote control sensor. 3. Replace all the batteries.
How to fix a Yamaha R-S201 remote control that is not working?
If the remote control for your Yamaha Receiver isn't working, ensure you're within 6 meters (20 feet) and within a 30-degree angle of the front panel. Reposition the unit if direct sunlight or strong lighting is interfering with the remote control sensor. Replace all the batteries, as weak batteries can cause the remote to malfunction.
Why is there no sound coming from my Yamaha Receiver?
If there is no sound from your Yamaha Receiver, first, ensure all input and output cables are correctly connected, and replace any defective cables. Select the appropriate input source using the Input selector buttons on the remote or front panel. Check that the SPEAKERS A/B switches are properly set. Ensure speaker connections are secure and deactivate the mute function. Verify that the MAX VOL or INITIAL VOLUME setting isn't too low. Lastly, confirm that the component connected to the selected input source is turned on and playing.
What to do if the remote control for my Yamaha R-S201 Receiver does not work?
If the remote control for your Yamaha Receiver isn't working, make sure you are within a 6 m (20 ft) range and no more than 30 degrees off-axis from the front panel. Reposition the unit if direct sunlight or lighting is interfering with the remote control sensor. Finally, replace all the batteries, if they are weak.
Why does the sound suddenly go off on my Yamaha R-S201 Receiver?
The sound on your Yamaha Receiver might suddenly go off because the protection circuitry has been activated due to a short circuit. Check the speaker wires to ensure they are not touching each other and then turn the power back on. Another reason could be that the unit has become too hot, so ensure the openings on the top panel are not blocked. Also, the AUTO POWER STANDBY or SLEEP function might have set the unit to standby mode; change the AUTO POWER STANDBY setting to a longer setting or OFF from the Option menu.
What to do if there is no sound from my Yamaha Receiver?
If there is no sound from your Yamaha Receiver, check the input and output cable connections to ensure they are properly connected. Select the appropriate input source using the Input selector buttons. Make sure the SPEAKERS A/B switches are correctly set. Ensure speaker connections are secure and that the mute function is deactivated. Verify that the MAX VOL or INITIAL VOLUME setting is not set too low. Lastly, confirm that the component corresponding to the selected input source is turned on and playing.
General| Receiver type | - |
|---|---|
| Frequency range | 10 - 100000 Hz |
| Input sensitivity | 500 mV |
| Audio output channels | - channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.2 % |
| Dynamic power per channel (4 Ohm) | 165 W |
| Dynamic power per channel (8 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 100 W |
| FM antenna ports quantity | 1 |
| Ethernet LAN | No |
| Supported radio bands | AM, FM |
| Display | LCD |
| Product color | Silver |
| Volume control | Rotary |
| Apple docking compatibility | Not supported |
| AC input voltage | 100-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.5 W |
Weight and Dimensions| Depth | 322 mm |
|---|---|
| Width | 435 mm |
| Height | 141 mm |
| Weight | 6700 g |
Explains symbols for dangerous voltage and important instructions in accompanying literature.
Warns against modifying the unit as it may void FCC authorization.
Details the controls and indicators located on the front of the unit.
Explains the indicators and display elements on the front panel.
Details the connections and terminals located on the rear of the unit.
Explains the functions and buttons of the remote control.
Step-by-step guide on how to select and play an audio source.
Addresses common operational issues and their solutions.
Solutions for problems related to FM/AM reception and tuning.
To Next Page
