Why isn't my iPhone/iPod charging on my Yamaha R-S500 Receiver's Universal Dock?
If your iPhone/iPod is not charging on the Universal Dock connected to your Yamaha Receiver: * Ensure that this unit is turned on or set to standby mode. * Make sure the iPhone/iPod is securely connected to the Universal Dock for iPod.
How to fix Yamaha R-S500 Receiver remote control when it's not working?
If the remote control for your Yamaha Receiver isn't working properly, ensure you are within 6 meters (20 ft) and within 30 degrees of the front panel. Check for direct sunlight or lighting interfering with the remote sensor and reposition the unit if necessary. Replace weak batteries. Verify that the remote control ID matches the unit's ID, and that the remote control code is correctly set. Press the input selector button corresponding to the component you're trying to control. Ensure the remote is set to the correct zone (Main or Zone 2). If batteries were weak or removed, reset the remote control ID and zone.
How to fix a Yamaha Receiver remote control that is not working?
If the remote control for your Yamaha Receiver isn't working properly, ensure you're within a 6 m (20 ft) range and no more than 30 degrees off-axis from the front panel. Reposition the unit if direct sunlight or strong lighting is affecting the remote control sensor. Replace weak batteries. Check if the remote control ID matches the unit’s ID, and switch them if necessary. If that doesn't work, try setting another code from the “LIST OF REMOTE CONTROL CODES”. For components, press the input selector button corresponding to the component you are trying to control, and then press the desired remote control button(s). Also, replace all batteries, and then set the remote control ID again.
Why can't I tune in to the desired station with the automatic tuning method on my Yamaha Receiver?
If the desired station cannot be tuned in with the automatic tuning method on your Yamaha Receiver, the signal may be weak or the antenna connections may be loose. Tighten the AM loop antenna connections and orient it for the best reception.
Why isn't my iPhone/iPod charging with the Yamaha Wireless System for iPod?
If your iPhone/iPod is not charging when using the Wireless System for iPod with your Yamaha Receiver: * Ensure that this unit is turned on or set to standby mode. * Verify that the YID-W10 transmitter is stationed securely in the YID-W10 receiver.
Why is the sound level low on my Yamaha R-S500?
If the sound level is low on your Yamaha Receiver, it could be due to the loudness control function operating. Try turning down the volume, setting the LOUDNESS control to the FLAT position, and then adjusting the volume again.
How to stop crackling and hissing noises on Yamaha R-S500?
To address continuous crackling and hissing noises with your Yamaha Receiver, consider that the noises may result from lightning, fluorescent lamps, motors, thermostats or other electrical equipment. Try using an outdoor antenna and a earth ground. This will help somewhat, but it is difficult to eliminate all noise.
What to do if the sound suddenly goes off on a Yamaha R-S500?
If the sound on your Yamaha Receiver suddenly goes off, here's what you can check: * The protection circuitry may have been activated due to a short circuit. Ensure the IMPEDANCE SELECTOR switch is in the correct position. * Make sure the speaker wires are not touching each other and then turn the power of this unit back on. * The unit may have become too hot; ensure the openings on the top panel are not blocked. * The automatic power down function might have turned the unit off. Change the automatic power down setting (“APD TIMER” in the Advanced Setup menu) to a longer setting, or disable the automatic power down function by setting the POWER MANAGEMENT switch on the rear panel to OFF.
What to do if the Bluetooth component is not found on Yamaha R-S500?
Try pairing again.
How to fix a Yamaha R-S500 that fails to turn on?
If your Yamaha receiver isn't turning on, consider these possible causes and solutions: 1. Ensure the power cable is firmly connected to both the receiver and the power outlet. 2. Verify the impedance setting matches your speakers. 3. Check for short circuits in the speaker wires; ensure they are not touching each other. Then, turn the receiver back on. 4. Confirm the IMPEDANCE SELECTOR switch on the rear panel is set to either end, with the power off during adjustment. 5. If the unit experienced a strong electrical shock, turn it off, unplug it for 30 seconds, then plug it back in and try again.
General| Frequency range | 10 - 10000 Hz |
|---|---|
| Audio output channels | 2.0 channels |
| Signal-to-Noise Ratio (SNR) | 74 dB |
| Total Harmonic Distortion (THD) | 0.015 % |
| Dynamic power per channel (4 Ohm) | 150 W |
| Dynamic power per channel (8 Ohm) | 105 W |
| Power output per channel (1KHz@8 Ohm) | 115 W |
| Power output per channel (20-20KHz@8 Ohm) | 75 W |
| Line-in | Yes |
| Audio (L/R) in | 6 |
| Audio (L/R) out | 2 |
| Connectivity technology | Wired |
| Speakers connectivity type | Clamp terminals |
| Ethernet LAN | No |
| Supported radio bands | AM, FM |
| Preset stations quantity | 40 |
| Display | - |
| Product color | Silver |
| Apple docking compatibility | Not supported |
| Power consumption (standby) | 0.5 W |
Weight and Dimensions| Depth | 387 mm |
|---|---|
| Width | 435 mm |
| Height | 151 mm |
| Weight | 10200 g |
Guidance on selecting a proper, safe, and well-ventilated location for the unit.
Detailed description of buttons and indicators on the unit's front panel.
Explanation of the various indicators shown on the front panel display.
Overview of all input and output terminals on the rear panel of the unit.
Description of buttons on the main remote control for operating the unit.
Guide to connecting speakers, turntables, tape decks, and other audio components.
Instructions for IMPEDANCE SELECTOR switch and bi-wire connections for speakers.
Steps to select an input source, play it, and adjust volume and tone.
Using CD DIRECT AMP and PURE DIRECT for enhanced sound quality.
How to adjust the BASS, TREBLE, and BALANCE controls for desired sound.
Overview of SIRIUS Satellite Radio service, availability, and features.
Guide to connecting the SiriusConnect tuner to the unit.
Steps to activate your SIRIUS Satellite Radio subscription and find your Sirius ID.
Overview of connecting Yamaha docks, wireless systems, or Bluetooth receivers.
Guide to accessing and setting options specific to each input source.
Overview of initial settings available in the Advanced Setup menu.
Using the remote to control the unit, TVs, and other audio-visual components.
Common problems and solutions for unit power, sound, and basic functions.
To Next Page
