Yamaha R-S500 User Manual (English)

Questions and Answers:

J
Jason GutierrezAug 30, 2025
What to do if the sound suddenly goes off on a Yamaha R-S500?
- M
  Megan MorrisAug 30, 2025
  If the sound on your Yamaha Receiver suddenly goes off, here's what you can check: * The protection circuitry may have been activated due to a short circuit. Ensure the IMPEDANCE SELECTOR switch is in the correct position. * Make sure the speaker wires are not touching each other and then turn the power of this unit back on. * The unit may have become too hot; ensure the openings on the top panel are not blocked. * The automatic power down function might have turned the unit off. Change the automatic power down setting (“APD TIMER” in the Advanced Setup menu) to a longer setting, or disable the automatic power down function by setting the POWER MANAGEMENT switch on the rear panel to OFF.
M
matthewellisSep 6, 2025
Why isn't my iPhone/iPod charging on my Yamaha R-S500 Receiver's Universal Dock?
- H
  hatfieldcrystalSep 6, 2025
  If your iPhone/iPod is not charging on the Universal Dock connected to your Yamaha Receiver: * Ensure that this unit is turned on or set to standby mode. * Make sure the iPhone/iPod is securely connected to the Universal Dock for iPod.
T
turnertimothyAug 29, 2025
What to do if the Bluetooth component is not found on Yamaha R-S500?
- R
  Rebecca BanksAug 29, 2025
  Try pairing again.
K
Kara LongSep 8, 2025
Why can I only hear the speaker on one side on my Yamaha Receiver?
- M
  matthew61Sep 8, 2025
  If you only hear sound from one speaker connected to your Yamaha Receiver, first, ensure that all cable connections are correct and that none of the cables are defective. Next, check the BALANCE control setting and adjust it to the appropriate position.
V
vwagnerSep 7, 2025
What does 'Not found' mean on Yamaha R-S500?
- J
  Jonathan JohnsonSep 8, 2025
  If your Yamaha Receiver displays 'Not found' when trying to connect a Bluetooth device: * During pairing: Pairing must be performed on the Bluetooth component and this unit simultaneously. Check if the Bluetooth component is in pairing mode. * During connecting: Check if the Bluetooth component is turned on and if the Bluetooth component is within 10 m (32 feet) of the Bluetooth Wireless Audio Receiver. Pairing may not have been achieved. Try pairing again.
A
Anthony HallAug 27, 2025
What to do if the sound on my Yamaha Receiver suddenly goes off?
- A
  Anne MartinezAug 27, 2025
  If the sound suddenly goes off on your Yamaha Receiver, check that the IMPEDANCE SELECTOR switch is set to the correct position. Also, ensure that the openings on the top panel are not blocked, as the unit may have become too hot. If the automatic power down function is enabled, adjust the “APD TIMER” setting in the Advanced Setup menu or disable it by setting the POWER MANAGEMENT switch on the rear panel to OFF.
J
Julie MezaAug 26, 2025
What to do if my Yamaha R-S500 Receiver fails to turn on?
- V
  Virginia DiazAug 27, 2025
  If your Yamaha Receiver fails to turn on, ensure the power cable is firmly connected. Check that the impedance setting matches your speakers. Also, verify that the speaker wires aren't touching each other, as this could activate the protection circuitry. Confirm that the IMPEDANCE SELECTOR switch on the rear panel is correctly set. If the unit experienced a strong electric shock, put it in standby, disconnect the power, wait 30 seconds, and then reconnect it.
M
Michael KingAug 26, 2025
Why can't I tune in to the desired station with the automatic tuning method on my Yamaha Receiver?
- C
  Clifford LambertAug 26, 2025
  If the desired station cannot be tuned in with the automatic tuning method on your Yamaha Receiver, the signal may be weak or the antenna connections may be loose. Tighten the AM loop antenna connections and orient it for the best reception.
T
Timothy TranAug 25, 2025
How to fix a Yamaha Receiver remote control that is not working?
- S
  Sarah MyersAug 26, 2025
  If the remote control for your Yamaha Receiver isn't working properly, ensure you're within a 6 m (20 ft) range and no more than 30 degrees off-axis from the front panel. Reposition the unit if direct sunlight or strong lighting is affecting the remote control sensor. Replace weak batteries. Check if the remote control ID matches the unit’s ID, and switch them if necessary. If that doesn't work, try setting another code from the “LIST OF REMOTE CONTROL CODES”. For components, press the input selector button corresponding to the component you are trying to control, and then press the desired remote control button(s). Also, replace all batteries, and then set the remote control ID again.
R
robert40Aug 25, 2025
How to fix Yamaha R-S500 Receiver remote control when it's not working?
- J
  juan44Aug 25, 2025
  If the remote control for your Yamaha Receiver isn't working properly, ensure you are within 6 meters (20 ft) and within 30 degrees of the front panel. Check for direct sunlight or lighting interfering with the remote sensor and reposition the unit if necessary. Replace weak batteries. Verify that the remote control ID matches the unit's ID, and that the remote control code is correctly set. Press the input selector button corresponding to the component you're trying to control. Ensure the remote is set to the correct zone (Main or Zone 2). If batteries were weak or removed, reset the remote control ID and zone.

Yamaha R-S500 Specifications

General

Frequency range	10 - 10000 Hz
Audio output channels	2.0 channels
Signal-to-Noise Ratio (SNR)	74 dB
Total Harmonic Distortion (THD)	0.015 %
Dynamic power per channel (4 Ohm)	150 W
Dynamic power per channel (8 Ohm)	105 W
Power output per channel (1KHz@8 Ohm)	115 W
Power output per channel (20-20KHz@8 Ohm)	75 W
Line-in	Yes
Audio (L/R) in	6
Audio (L/R) out	2
Connectivity technology	Wired
Speakers connectivity type	Clamp terminals
Ethernet LAN	No
Supported radio bands	AM, FM
Preset stations quantity	40
Display	-
Product color	Silver
Apple docking compatibility	Not supported
Power consumption (standby)	0.5 W