To Next PageTo Next PageWhat to do if Yamaha RDX-E700 Receiver power turns on but immediately shuts off?
First, ensure the power cable is firmly plugged into the outlet. Next, check all speaker cables to ensure they are properly connected and not shorted. If the receiver experienced a strong electrical shock, set it to Standby, disconnect the power cable for 30 seconds, then reconnect and turn it on.
Why do the speakers make no sound on my Yamaha RDX-E700?
Several factors could be at play. Check that the volume isn't set too low and that the Mute function is disabled. Also, verify you've selected the correct input source and that all cables are properly connected. If you're using a disc, ensure it's compatible with the receiver. Finally, if playing a DTS source, make a digital connection to a component with a DTS decoder and select “RAW” for “DIGITAL OUTPUT” in the OSD menu.
What to do if Yamaha remote control does not work for operating the DVD receiver?
The remote control may be operated outside the remote control operation range. The remote control sensor on the DVD receiver may be exposed to direct sunlight or lighting (inverted fluorescent lamps), so change the lighting or DVD receiver’s orientation. The remote control mode selection may be improper, so select the mode that suits your purpose. The batteries may be worn out, so replace the batteries with new ones.
Why Yamaha remote control does not work for operating TV?
The remote control code may be incorrect. Set the correct remote control code. Depending on the model and year of the product, the remote control may not be able to operate it partly or wholly. In this case, use the remote control supplied for the product.
Why do my Yamaha Receiver speakers make no sound?
If your Yamaha Receiver speakers aren't producing sound, there are several potential causes: * The volume might be set too low; try increasing it. * The Mute function could be enabled; disable it. * The input source may be incorrect; select the correct one. * Cables might be improperly connected; ensure all cables are correctly attached. * The disc may be incompatible; use a supported disc. * If playing a DTS source, make a digital connection to a component with a DTS decoder and select “RAW” for “DIGITAL OUTPUT” with the OSD menu.
Why does my Yamaha Receiver remote control not work?
If the remote control isn't operating the Yamaha Receiver, consider these possibilities: * You may be operating the remote outside of its operational range. * The remote sensor on the receiver might be exposed to direct sunlight or certain lighting; try adjusting the lighting or receiver's orientation. * The remote control mode selection may be incorrect; select the correct mode. * The batteries may be worn out; replace them with new ones.
How to fix Yamaha RDX-E700 Receiver remote control that doesn't work?
If your Yamaha Receiver remote control isn't working, consider these potential causes: * You may be operating the remote outside of its operational range. * The remote control sensor on the DVD receiver may be exposed to direct sunlight or certain types of lighting. * The remote control mode selection may be incorrect. * The batteries may be worn out; try replacing them.
How to reduce noise during stereo broadcast on my Yamaha RDX-E700 Receiver?
If you are experiencing too much noise during stereo broadcast on your Yamaha Receiver, the FM antenna may be connected improperly. Make sure the FM antenna is connected properly. Also, the radio station you selected may be far away from your area or radio wave reception is weak in your area. Try Manual Tuning to increase the signal quality or use a multi-channel outdoor antenna.
What if the disc loaded into my Yamaha RDX-E700 Receiver is not compatible?
If the disc loaded into the Yamaha Receiver may be not compatible, make sure you use a disc supported by the DVD receiver.
How to stop Yamaha RDX-E700 Receiver from generating too much noise?
If too much noise is generated from your Yamaha Receiver, the noises may be generated from atmospheric electricity, lightening, fluorescent lights, motors, or thermostat electric devices. Connect an outdoor antenna and establish better grounding to decrease noises. However, it is difficult to eliminate these types of noises. If too much noise is generated especially in the evening, the DVD receiver may be placed close to a TV. Place the DVD receiver further away from a TV.
General| Type | Receiver |
|---|---|
| Audio Channels | 2.1 |
| Remote Control | Yes |
| Speaker Impedance | 6 ohms |
| Amplifier Type | Digital |
| Output Power | 100W per channel (6 ohms, 1kHz, 10% THD) |
