Why doesn't the Auto Tuning function work on my Yamaha Receiver AM?
If the Auto Tuning function does not work on your Yamaha Receiver, the AM loop antenna may be connected improperly. Make sure the AM loop antenna is connected properly. Also, the radio station you selected may be far away from your area or radio wave reception is weak in your area. Try Manual Tuning to increase the signal quality.
What to do if my Yamaha RDX-E700 Receiver power turns on but immediately shuts off?
If your Yamaha Receiver turns on but immediately shuts off, it could be due to a few reasons. First, ensure the power cable is firmly plugged into the outlet. Second, check the speaker cables to make sure they are properly connected and not shorted. Lastly, if the receiver experienced a strong electrical shock, set it to Standby mode, disconnect the power cable for 30 seconds, then reconnect and turn it on.
Why has the clock setting been cleared on my Yamaha RDX-E700 Receiver?
If the clock setting on your Yamaha Receiver has been cleared, it's likely the receiver lost power for more than a week. Make sure the power cable is plugged into the outlet firmly, then set the clock again.
What to do if Yamaha playback does not start immediately when pressing play?
The disc may not be set in the disc tray properly, so set the disc in the disc tray properly. The disc may be dirty, so wipe the disc clean. The disc loaded into the DVD receiver may be not compatible, so make sure you use a disc supported by the DVD receiver. When moved the DVD receiver from a cold place to warm one, condensation may be form on the disc reading lens, so wait for one to two hours, then try again.
Why Yamaha Receiver auto tuning function does not work?
If the Auto Tuning function on your Yamaha Receiver isn't working, it could be because the AM loop antenna may be connected improperly. Make sure the AM loop antenna is connected properly. Also, the radio station you selected may be far away from your area or radio wave reception is weak in your area. Try Manual Tuning to increase the signal quality.
Why does the TV show overlapped picture partly with my Yamaha RDX-E700 Receiver?
If the TV shows overlapped picture partly with your Yamaha Receiver, the disc content does not match the Progressive Scan mode due to the editing method or other conditions. Turn off the Progressive Scan mode.
Why does the sound on my Yamaha Receiver suddenly turn off?
If the sound on your Yamaha Receiver suddenly turns off, the sleep timer might be set. Turn on the DVD receiver and play the source again.
Why Yamaha RDX-E700 source does not record when using an external component?
If a source being played back on the Yamaha Receiver does not record when using an external component, you may be trying to make a digital recording of an AM/FM broadcast. Use the analog recording method.
What to do if Yamaha preset station settings have been cleared?
If the preset station settings have been cleared, the power to the DVD receiver may have been lost for more than a week. Make sure the power cable is plugged into outlet firmly, then preset the stations again.
How to fix Yamaha RDX-E700 Receiver remote control that doesn't work?
If your Yamaha Receiver remote control isn't working, consider these potential causes: * You may be operating the remote outside of its operational range. * The remote control sensor on the DVD receiver may be exposed to direct sunlight or certain types of lighting. * The remote control mode selection may be incorrect. * The batteries may be worn out; try replacing them.
Details on components requiring exact replacement due to special characteristics.
Procedure to verify proper insulation of conductive surfaces after service.
Information on laser beam emission during operation and handling precautions.
Essential steps for grounding worktables and personnel to prevent static damage.
Specific precautions for handling the high-precision DVD mechanism to avoid damage.
Technical details for the amplifier, including output power, distortion, and sensitivity.
Covers power supply, consumption, weight, dimensions, and included accessories.
Step-by-step guide for safely removing the RDX-E700's top cover.
Step-by-step guide for safely removing the RDX-E700's front panel.
Step-by-step guide for safely removing the RDX-E700's DVD mechanism.
Detailed steps to reset the DVD Mechanism Assy to factory default settings.
Part details for the RDX-E700 sub panel assembly.
Part details for the RDX-E700 power supply unit.
Part details for the RDX-E700 DVD mechanism assembly.
General| Type | Receiver |
|---|---|
| Audio Channels | 2.1 |
| Remote Control | Yes |
| Speaker Impedance | 6 ohms |
| Amplifier Type | Digital |
| Output Power | 100W per channel (6 ohms, 1kHz, 10% THD) |
To Next Page
