To Next PageTo Next PageWhy does the sound on my Yamaha Receiver suddenly turn off?
If the sound on your Yamaha Receiver suddenly turns off, the sleep timer might be set. Turn on the DVD receiver and play the source again.
Why does my Yamaha RDX-E700 show no picture on TV?
If your TV shows no picture when connected to the Yamaha Receiver, the cables may be connected improperly. Ensure all cables are connected properly.
How to fix too much noise during Yamaha RDX-E700 Receiver stereo broadcast?
Excessive noise during stereo broadcast on your Yamaha Receiver can be due to: * The FM antenna may be connected improperly; ensure it's properly connected. * The selected radio station may be too far away or radio wave reception is weak; try Manual Tuning to increase the signal quality or use a multi-channel outdoor antenna.
Why Yamaha RDX-E700 picture is not showing properly on TV?
If the TV isn't showing the picture properly with your Yamaha Receiver: * The picture settings may be improper; adjust them using the OSD menu. * The Progressive Scan mode may be used with a TV that doesn't support it; turn off Progressive Scan mode.
How to reduce noise generated by Yamaha RDX-E700?
Excessive noise from the Yamaha Receiver can stem from: * Atmospheric electricity, lightning, fluorescent lights, motors, or thermostat electric devices. Connect an outdoor antenna and establish better grounding to decrease noises. However, it is difficult to eliminate these types of noises. * Proximity to a TV, especially in the evening. Place the DVD receiver further away from the TV.
How to stop Yamaha RDX-E700 Receiver from generating too much noise?
If too much noise is generated from your Yamaha Receiver, the noises may be generated from atmospheric electricity, lightening, fluorescent lights, motors, or thermostat electric devices. Connect an outdoor antenna and establish better grounding to decrease noises. However, it is difficult to eliminate these types of noises. If too much noise is generated especially in the evening, the DVD receiver may be placed close to a TV. Place the DVD receiver further away from a TV.
What if the disc loaded into my Yamaha RDX-E700 Receiver is not compatible?
If the disc loaded into the Yamaha Receiver may be not compatible, make sure you use a disc supported by the DVD receiver.
How to reduce noise during stereo broadcast on my Yamaha RDX-E700 Receiver?
If you are experiencing too much noise during stereo broadcast on your Yamaha Receiver, the FM antenna may be connected improperly. Make sure the FM antenna is connected properly. Also, the radio station you selected may be far away from your area or radio wave reception is weak in your area. Try Manual Tuning to increase the signal quality or use a multi-channel outdoor antenna.
Why does my Yamaha RDX-E700 Receiver produce noises when using digital equipment?
If a digital equipment or high-frequency equipment produces noises with your Yamaha Receiver, the DVD receiver may be placed close to the digital equipment or high-frequency equipment. Place the DVD receiver further away from such equipment.
Why does my Yamaha Receiver remote control not work?
If the remote control isn't operating the Yamaha Receiver, consider these possibilities: * You may be operating the remote outside of its operational range. * The remote sensor on the receiver might be exposed to direct sunlight or certain lighting; try adjusting the lighting or receiver's orientation. * The remote control mode selection may be incorrect; select the correct mode. * The batteries may be worn out; replace them with new ones.
Details on components requiring exact replacement due to special characteristics.
Procedure to verify proper insulation of conductive surfaces after service.
Information on laser beam emission during operation and handling precautions.
Essential steps for grounding worktables and personnel to prevent static damage.
Specific precautions for handling the high-precision DVD mechanism to avoid damage.
Technical details for the amplifier, including output power, distortion, and sensitivity.
Covers power supply, consumption, weight, dimensions, and included accessories.
Step-by-step guide for safely removing the RDX-E700's top cover.
Step-by-step guide for safely removing the RDX-E700's front panel.
Step-by-step guide for safely removing the RDX-E700's DVD mechanism.
Detailed steps to reset the DVD Mechanism Assy to factory default settings.
Part details for the RDX-E700 sub panel assembly.
Part details for the RDX-E700 power supply unit.
Part details for the RDX-E700 DVD mechanism assembly.
General| Type | Receiver |
|---|---|
| Audio Channels | 2.1 |
| Remote Control | Yes |
| Speaker Impedance | 6 ohms |
| Amplifier Type | Digital |
| Output Power | 100W per channel (6 ohms, 1kHz, 10% THD) |
