Why does my Yamaha RX-V3900 say 'No Device' when a USB is plugged in?
If “No Device” is displayed even when a USB device is connected to your Yamaha Receiver, the unit may have recognized the USB storage device as an illegal device. Try turning the unit off and then on again. Also, ensure that music files and directories are placed in the FAT area of the USB device.
How to fix no sound on my Yamaha Receiver?
If you're experiencing no sound from your Yamaha Receiver, try these steps: First, ensure that all input and output cables are correctly connected and not defective. Make sure the audio input jack select is set to “AUTO”. If it's set to “ANALOG”, but your input source outputs digital audio, switch it to “COAX/OPT”. Select the appropriate input source using the input selector. Also, check that the volume isn't turned down or muted. Finally, ensure that the source you're playing can be reproduced by the unit and supports HDCP copy protection standards.
Why is there no sound coming from my Yamaha RX-V3900?
There could be several reasons for the lack of sound from your Yamaha Receiver. Check the following: * Ensure the cables are connected properly; if the problem persists, they may be defective. * Verify that the audio input jack select is set to “AUTO”. * Make sure an appropriate input source is selected using the CINPUT selector or input selector buttons. * Confirm that the volume is not turned down or muted. * Ensure the input source signals can be reproduced by the unit. * If using HDMI, check that the connected components support HDCP copy protection standards.
What to do if my Yamaha Receiver fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, there might be a few reasons. First, ensure the power cable is firmly connected. Also, verify that the speaker impedance setting matches your speakers. It's also possible that the protection circuitry has been activated; in this case, check all speaker wire connections to ensure they are secure and not touching anything else. If the unit experienced a strong electric shock, turn it off, disconnect the power cable, wait 30 seconds, and then plug it back in.
Why can't I play Internet Radio on my Yamaha RX-V3900?
If Internet Radio cannot be played on your Yamaha Receiver, the firewall of the network device may be activated. Check the firewall setting of the network device.
How to troubleshoot no picture on Yamaha RX-V3900?
If you're not getting a picture from your Yamaha Receiver, ensure your video monitor is connected to the HDMI OUT or COMPONENT VIDEO MONITOR OUT jacks, especially if it's connected to an analog video output. If using 1080p-resolution analog video signals, these are only output at the COMPONENT VIDEO MONITOR OUT jacks. You may need to set “Analog ? Analog” to “Conversion” or connect your source components in the same way as you connect your video monitor to this unit. Also, ensure the unit outputs video signals supported by the video monitor connected to the HDMI OUT jack.
Why is there no sound from the center speaker on my Yamaha RX-V3900?
If you are not hearing sound from the center speaker on your Yamaha Receiver, it might be because the unit is in “STRAIGHT” mode while playing a monaural source; press NSTRAIGHT to turn off the “STRAIGHT” mode. Another reason could be that “Center” in “Configuration” is set to “None”; change it to “Small” or “Large”.
Why no sound from surround speakers Yamaha Receiver?
If you're not hearing sound from the surround speakers on your Yamaha Receiver, check if “Surround” in “Configuration” is set to “None”.
What does 'CHECK SP WIRES' mean on Yamaha Receiver?
If “CHECK SP WIRES” appears on the front panel display of your Yamaha Receiver, it indicates that the speaker cables are short-circuited. Ensure that all speaker cables are connected correctly.
How to troubleshoot no sound on a Yamaha RX-V3900 Receiver?
If you are not getting any sound from your Yamaha Receiver, first ensure that all input and output cables are connected properly; if the problem continues, the cables may be defective. If the audio input jack select is set to “HDMI”, “COAX/OPT” or “ANALOG”, set it to “AUTO”. If set to “ANALOG” while the input source uses digital audio signals, set it to “COAX/OPT”. Also, make sure you have selected an appropriate input source using the input selector. Check that the volume isn't turned down or muted. Finally, ensure that the source signals can be reproduced by the unit and that connected HDMI components support HDCP copy protection standards.
General| Channels | 7.1 |
|---|---|
| HDMI Inputs | 6 |
| HDMI Outputs | 2 |
| HDMI Version | 1.3a |
| Bluetooth | No |
| Wi-Fi | No |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio, Dolby Digital, DTS, PCM |
| Video Formats Supported | 1080p |
| THD (Total Harmonic Distortion) | 0.06% |
| Frequency Response | 10 Hz - 100 kHz |
| Dimensions (W x H x D) | 435 x 192 x 467 mm (17-1/8" x 7-9/16" x 18-3/8") |
| Inputs | HDMI, Component Video, Composite Video, Digital Optical, Digital Coaxial |
| Outputs | HDMI, Component Video, Composite Video, Analog Audio |
| Video Upscaling | Yes |
| Network Features | Ethernet, Internet Radio |
| Power Output | 140 W per channel (8 ohms, 20 Hz - 20 kHz, 0.06% THD, 2 channels driven) |
To Next Page
