What to do if Dolby Digital or DTS sources cannot be played on Yamaha Receiver?
If Dolby Digital or DTS sources cannot be played on your Yamaha Receiver, and the Dolby Digital or DTS indicator does not light up, ensure that the connected component is set to output Dolby Digital or DTS digital signals by following its operating instructions. Also, verify that the input mode is set to AUTO or DTS, not ANALOG.
Why can I only hear sound from one speaker on my Yamaha RX-V657 Receiver?
If you only hear sound from one speaker on your Yamaha Receiver, ensure that all cable connections are correct and secure. If the problem persists, the cables may be defective. Additionally, check the balance settings in the SET MENU and adjust the SPEAKER LEVEL settings to ensure proper balance between the speakers.
How to fix on-screen display not appearing on Yamaha RX-V657?
If the on-screen display does not appear on your Yamaha Receiver, check if the on-screen display setting is set to “DISPLAY OFF”. If so, select the full display or short display mode. Also, if “GRAY BACK” in SET MENU is set to OFF and no video signal is being received, set “GRAY BACK” to AUTO to always show the OSD.
What to do if my Yamaha RX-V657 Receiver fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, ensure the power cord is firmly connected to the unit and the outlet. Verify that the impedance setting matches your speakers. Check all speaker wire connections to ensure they are secure and not touching anything other than their respective connections, as the protection circuitry may have been activated. If the unit has been exposed to a strong external electric shock, set it to standby mode, disconnect the power cord, plug it back in after 30 seconds, and then try using it normally.
Why is there no sound coming from the effect speakers on my Yamaha RX-V657?
If there's no sound from the effect speakers on your Yamaha receiver, try these solutions: * Press STRAIGHT (EFFECT) to turn on the sound field programs if they are turned off. * Try another sound field program, as you may be using a source or program combination that does not output sound from all channels.
Why is there no sound coming from the center speaker of my Yamaha Receiver?
If there's no sound from the center speaker of your Yamaha receiver, try these solutions: * Increase the level of the center speaker if its output level is set to minimum. * Check if “CENTER SP” in SET MENU is set to NONE; if so, select the appropriate setting for the center speaker. * If one of the HiFi DSP programs (except for 7ch Stereo) is selected, try another sound field program.
Why do my Yamaha Receiver surround speakers have no sound?
If you are not getting any sound from the surround speakers connected to your Yamaha Receiver, consider the following: * Ensure that the output level of the surround speakers is not set to minimum; increase the output level if necessary. * Check that “SUR. L/R SP” in SET MENU is not set to NONE; select the appropriate setting for the surround left and right speakers. * If playing a monaural source with STRAIGHT, press STRAIGHT (EFFECT) to turn on the sound fields.
Why is there no sound from the subwoofer on my Yamaha Receiver?
If you're not getting any sound from the subwoofer connected to your Yamaha receiver, check the following: * In the SET MENU, if “LFE/BASS OUT” is set to FRNT while playing a Dolby Digital or DTS signal, change it to SWFR or BOTH. * If “LFE/BASS OUT” is set to SWFR or FRNT when playing a 2-channel source, select BOTH. * The source might not contain low bass signals.
Why is there no sound from the effect speakers on my Yamaha RX-V657 Receiver?
If there is no sound from the effect speakers on your Yamaha Receiver, ensure that the sound field programs are turned on by pressing STRAIGHT (EFFECT). If you are using a source or program combination that does not output sound from all channels, try another sound field program.
Why is there no sound from the surround back speakers on my Yamaha RX-V657 Receiver?
If there is no sound from the surround back speakers on your Yamaha Receiver, ensure that surround back speakers are selected in SUR. B L/R SP. If “SUR. L/R SP” in SET MENU is set to NONE, the surround back speaker setting is automatically set to NONE, so select the appropriate setting for the surround speakers. Also, check that “SUR. B L/R SP” in SET MENU is set to LRGx1 or SMLx1.
General| Audio Channels | 7.1 |
|---|---|
| Total Harmonic Distortion (THD) | 0.06% |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 100 dB |
| Component Video Inputs | 3 |
| Composite Video Inputs | 4 |
| Digital Audio Inputs (Coaxial) | 2 |
| Response Bandwidth | 10 Hz - 100 kHz |
| Surround Sound Effects | Yes |
| Sound Effects | Yes |
| DSP Presets | 17 |
| Tuner Presets | 40 |
| Video Outputs (Composite) | 1 |
| Video Outputs (S-Video) | 1 |
| Video Outputs (Component) | 1 |
| Audio Inputs (Analog) | 6 |
| Audio Outputs (Analog) | 1 |
| Audio Outputs (Digital Optical) | 1 |
| Radio | AM/FM |
| Power Output (per channel) | 90 W |
| Frequency Response | 10 Hz - 100 kHz |
| Input Impedance | 47k ohms |
| Audio D/A Converter | 192kHz/24-bit |
| Built-in Decoders | Dolby Digital, DTS, Dolby Pro Logic II |
Explains the meaning of graphical symbols used in the manual for safety alerts and provides numbered safety instructions.
Details the unit's amplifier specifications, sound field technologies, tuner capabilities, XM Radio, and other features.
Lists supplied accessories and provides instructions for installing batteries in the remote control.
Identifies and describes the buttons and indicators located on the front panel of the unit.
Describes the functions of each button on the remote control for operating the unit.
Identifies and describes the various input and output jacks on the rear panel of the unit.
Provides recommended placement for front, center, surround, and presence speakers for optimal sound.
Details how to connect speaker cables to the unit's terminals, including wire preparation and banana plug use.
General advice before connecting components, including cable indications.
Instructions for connecting video sources like DVD players and monitors.
Instructions for connecting audio sources like CD players and MD decks.
Details how to connect the included indoor FM and AM loop antennas.
Introduces Yamaha Parametric Room Acoustic Optimizer (YPAO) and the setup procedure.
Explains how to connect and position the optimizer microphone for the auto setup.
Details the steps to initiate and run the YPAO auto setup process.
Interprets auto setup results and provides troubleshooting for common errors or warnings.
Covers core playback steps like powering on, selecting speakers, input source, and volume.
Explains how to use sound field programs and Silent Cinema for headphone listening.
Guides on choosing input sources and modes (AUTO, DTS, ANALOG) for digital inputs.
Explains automatic and manual tuning procedures for receiving FM/AM stations.
Details how to automatically and manually store FM stations using the preset tuning feature.
Covers service introduction, antenna connection, basic operations, and display switching.
Explains the three search modes (All Channel, Category, Preset) for finding XM channels.
Details the procedure to store desired XM channels as presets using the memory function.
Outlines the basic steps for recording audio and video from connected components.
Describes sound field programs optimized for movie/video and music sources.
Explains how to change OSD modes and set the sleep timer.
Guides on how to manually balance the output level of individual speakers.
Introduces the SET MENU for adjusting system settings and guides on its interface.
Lists detailed parameters within the Sound, Input, and Option menus.
Covers manual speaker configuration, distance, phase, and level adjustments.
Explains reassigning jacks, input modes, renaming inputs, and volume trim.
Guides on how to enter the Advanced Setup menu for initial parameter configuration.
Lists parameters configurable in the Advanced Setup Menu, including speaker impedance.
Explains how to use the remote control to operate the main unit.
Describes setting up the remote control to operate other A/V components.
Manages remote control library codes and clearing previously set codes.
Outlines necessary equipment and connections for setting up a multi-room audio system.
Explains how to enable and use the remote control to operate Zone 2 functions.
Explains the elements of a sound field and how to change parameter settings.
Details the steps to reset sound field parameters to their original factory settings.
Details how to adjust DSP effect levels, initial delay, and room size parameters.
Describes adjustments for sound reflectivity (liveness) and surround field size.
Explains how to adjust reverberation time, delay, and level to shape the acoustic environment.
Provides solutions for common problems like no power, no sound, and no picture.
Addresses issues related to sudden sound loss, side-only audio, or missing speaker output.
Covers problems with input signals, tuner reception, and remote control functionality.
Details the steps to reset all unit parameters to their original factory defaults.
Defines various audio technologies like Dolby Digital, DTS, and Pro Logic.
Explains sound field programs and technical audio terms.
Defines component video, composite video, and S-video signal systems.
Lists technical specifications for the audio output power, frequency response, and video sections.
Provides technical details for tuner sections, power supply, dimensions, and weight.
Lists default remote control codes for various TV brands.
Provides default remote control codes for VCR, Cable TV, and LD player brands.
Lists default remote control codes for CD players, MD/CD-R recorders, and tuners.
Lists default remote control codes for DVD players and DVD recorders.
To Next Page
