Why is the volume level low when playing a record on my Yamaha RX-V995 Receiver?
If the volume level is low when playing a record on your Yamaha Receiver, and you are using a turntable with an MC cartridge, the player should be connected to the unit through the MC head amplifier.
Why learning cannot be made successfully on Yamaha RX-V995?
If learning cannot be made successfully (the TRANSMIT/LEARN indicator does not light up or flash), consider these potential reasons: * The batteries of this remote controller and/or the other remote controller are weak. Replace the batteries (and press the RESET button for this remote controller). * The distance between the two remote controllers is too far or short. Place the remote controllers at the proper distance. * The signal coding or modulation of the other remote controller is not compatible with this remote controller. Learning is not possible. * Memory capacity is full. Further learning is not possible without deleting unnecessary commands. * The internal microcomputer 'freezes'. Press the RESET button on the remote controller.
Why a source cannot be recorded by a tape deck or VCR connected to Yamaha Receiver?
If a source cannot be recorded by a tape deck or VCR connected to your Yamaha Receiver, and the source unit is connected to this unit between digital terminals only, make additional connection between analog terminals.
What does “INPUT DATA ERR” mean on Yamaha RX-V995 Receiver?
If “INPUT DATA ERR” appears on the display of your Yamaha Receiver and no sound is heard, a nonstandardized source is being played back, or the unit playing back a source is misoperating. Check the source, or turn off the unit playing back the source and then turn it on again.
Why the volume level cannot be increased, or sound is distorted on Yamaha RX-V995?
If the volume level cannot be increased, or the sound is distorted on your Yamaha Receiver, the component connected to the TAPE/MD OUT terminals of this unit might be turned off. Turn on the power to that component.
Essential safety guidelines covering electrical hazards, installation, ventilation, and proper handling.
Explanation of hazard symbols like lightning flash and exclamation point for user awareness.
Guidelines for antenna grounding and FCC compliance notices regarding interference.
Important cautions on impedance selector, frequency step switches, and Canadian plug polarity.
Overview of the unit's amplification, tuner, DSP, Dolby, and DTS capabilities.
Explains Yamaha's DSP technology for recreating acoustic environments.
Details the Dolby Pro Logic Surround system for multi-channel audio.
Explains Dolby Digital (5.1) and DTS Digital Surround (6-channel) audio formats.
Combining Yamaha DSP with Dolby/DTS for theater-like sound experiences.
Lists the accessories included with the AV receiver.
Installing batteries, operation range, and potential interference with the remote control.
Identifies and describes primary controls on the AV receiver's front panel.
Explains functions of specific controls like INPUT SELECTOR, VOLUME, and input mode buttons.
Explains the various indicators and information shown on the unit's display panel.
Guidelines for setting up a five-speaker system, center speaker, and subwoofer for optimal sound.
Illustrates 5-speaker and 4-speaker system setups and notes.
Instructions for connecting audio/video sources using RCA cables and identifying terminals.
Connecting video sources, using VIDEO AUX terminals, and setting PAL/NTSC switch.
How to connect digital audio sources using optical or coaxial cables.
Important notes on digital connections, terminal care, and signal integrity.
Instructions for connecting combi-players with Dolby Digital RF output via an RF demodulator.
How to use S-Video for higher quality video connections and video signal superimpose.
How to connect external decoders using the unit's 6-channel inputs.
Detailed instructions on connecting main, center, rear speakers, and subwoofer wires.
How to set the impedance selector based on speaker impedance requirements.
Using unit's output terminals to connect external amplifiers for main, center, or rear speakers.
Instructions for connecting included AM loop and FM antennas to the unit.
Guidance on connecting external AM and FM antennas and using adapters.
Instructions for plugging the unit into AC power and utilizing switched outlets.
How to use the on-screen display and select different display formats.
Overview of SET MENU functions for speaker output modes: Center, Rear, Main.
Detailed settings for LFE/BASS OUT and MAIN LEVEL in the SET MENU.
Step-by-step guide to changing settings using the front panel or remote control.
Detailed steps for adjusting speaker levels to achieve proper balance using the built-in test tone.
How to choose an input source for audio and video playback.
Using VOLUME, BASS, TREBLE, and BALANCE controls for sound adjustment.
How to enter standby and important considerations for input source selection.
How to select input modes (AUTO, DTS, ANALOG) for sources with multiple signal types.
Important considerations for input mode selection, especially with DTS and for specific sources.
Instructions for recording the currently playing source to tape or MD.
How to record one source while monitoring another simultaneously.
How to adjust BALANCE, BASS, TREBLE, and BASS EXTENSION for sound shaping.
Procedures for automatically and manually tuning radio stations.
How to store favorite radio stations and recall them by preset number.
How to automatically tune and store FM stations with strong signals.
How to swap the memory positions of two preset radio stations.
How to turn on the DSP and select sound field programs for enhanced audio.
Descriptions of DSP programs 1-5 for music: Concert Hall, Church, Jazz Club, Rock Concert, Disco.
Descriptions of CINEMA DSP programs 6-10 for movies/TV: TV Sports, Mono Movie, Movie Theater 1 & 2, DTS Surround.
How to access and change settings within the SET MENU mode using front panel or remote.
Settings for speaker output modes (Center, Rear, Main) and levels, LFE/Bass Out.
Adjustments for Dolby Digital LFE Level, Dynamic Range, and DTS LFE Level.
Settings for Center Delay, Parameter Initialization, Memory Guard, TV/DBS Input, and Dimmer.
Explains the concept of sound fields and the role of DSP parameters.
Step-by-step guide to selecting and editing parameters using the remote.
Details on ROOM SIZE (venue size) and INIT. DELAY (source distance) parameters.
Details on LIVENESS (reflectivity) and REV. TIME (reverberation duration) parameters.
Details on REV. LEVEL (reverb volume) and S. DELAY (surround delay) parameters.
How to set the sleep timer to automatically turn the unit off after a specified time.
Overview of remote control keys, including input selectors, operation controls, and special function keys.
How to use and program the learning-capable keys on the remote.
Notes on using empty keys, documenting functions, and memory backup.
How to use operation control keys with the remote cover closed.
Examples of controlling CD players and VCRs using operation control keys.
How to execute programmed sequences of commands using macro keys.
Setting the MACRO switch for OFF, QUICK, or SLOW command transmission.
Step-by-step guide to teaching the remote new functions from other controllers.
How to program a sequence of commands onto a single macro key.
How to clear individual learned functions or all learned functions and macros.
Required optional products and connection diagrams for a dual-room audio/video setup.
Steps to enjoy audio/video in a second room using the unit's ZONE 2 features.
Solutions for common problems like unit not turning on, no sound/picture, and general operational faults.
Diagnosing and fixing problems with the remote controller, including battery issues and learning failures.
Resolving issues with FM reception, tuning, and DTS audio playback problems.
Details on power output, impedance, sensitivity, and frequency response for audio sections.
FM/AM tuning specs, power requirements, dimensions, weight, and included accessories.
Solutions for DSP setting locks, data errors, recording problems, and external noise.
Details on power output, impedance, sensitivity, and frequency response for audio sections.
FM/AM tuning specs, power requirements, dimensions, weight, and included accessories.
To Next Page
General
