EasyManua.ls Logo

Yamaha YSP-4300 - Page 79

Yamaha YSP-4300
171 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
HDMI/OSD (IC101 on DIGITAL P.C.B.) /
HDMI/OSD(DIGITALP.C.B. IC101)
DSP (IC501 on DIGITAL P.C.B.) /
DSP(DIGITALP.C.B. IC501)
Microprocessor (IC701 on DIGITAL P.C.B.) /
マイコン(DIGITALP.C.B. IC701)
Destination /
仕向け先
U, C, T, K, A, B, G, F, L, V, S, H, J is displayed.
リモコンの “決定” キーを押す度に、仕向け表示が変わります。
J U C G E B T A F K L V R H S J .....
System model name /
システムモデル名
4300: YSP-CU4300
3300: YSP-CU3300
p1.4300U
05.00.04
p. SET INFORMATION
This menu is used to write the model name and
destination to the back-up IC (EEPROM: IC703 on
DIGITAL P.C.B.).
When the following parts are replaced, the model
name and destination MUST be written by using this
menu to have proper operation.
DIGITAL P.C.B.
EEPROM: IC703 on DIGITAL P.C.B.
To write the model name and destination, short TP731
(connected to pin 140 of IC701) of DIGITAL P.C.B. and
GND first.
Then, enter the menu item “p-1. SYSTEM MODEL
NAME and DESTINATION” and write the model name
and target destination by selecting them.
(For details, refer to “WRITING SYSTEM MODEL NAME
AND DESTINATION”)
p-1. SYSTEM MODEL NAME and DESTINATION
Select the target destination by pressing the
“ENTER” key of the remote control repeatedly.
Start writing by pressing the “RETURN” key of
the remote control.
* When writing is completed, the power will
be turned off automatically.
p-2. FIRMWARE VERSION
The firmware version is displayed.
p. SETINFORMATION
モデル名と仕向け先をバックアップ ICDIGITAL
P.C.B. IC703)に書き込みます。
下記の部品を交換した場合、正常動作のために本メ
ニューでモデル名と仕向け先を書き込む必要があり
ます。
DIGITALP.C.B.
EEPROM:DIGITALP.C.B. IC703
モデル名と仕向け先を書き込むには、まず最初に
DIGITALP.C.B. TP731(IC701 140 ピンと接続)
GND をショートさせます。
それから “p-1.SYSTEMMODELNAMEand
DESTINATION” メニューで目的のモデル名と仕向け先
を選択し、書き込みます。
(詳細は “システムモデル名と仕向け先の書き込み”
を参照してください。
p-1. SYSTEMMODELNAMEandDESTINATION
リモコンの “決定” キーを繰り返し押して目的
の仕向け先を選択します。
リモコンの “戻る” キーを押して書き込みを開
始します。
書き込みが完了すると、自動的に電源が切
れます。
p-2. FIRMWAREVERSION
ファームウェアバージョンが表示されます。
79
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300/YSP-CU3300/
NS-WSW160
DRAFT

Other manuals for Yamaha YSP-4300

Related product manuals