YASKAWA yasnac lx3

~ 1, ,s HANDLE DIALS FOR SIMULTANEOUS CONTROL
OF UP TO TWO AXES+ ( Cent’d )
Table 5. I Selection of Move Amount in the
HANDLE Mode+
>1
Metric
Inch
xl
x 10
x 100
x 1000
x Icooo
x Icclooo
0.001 mmlgraduation
0.0001 in.lgraduation
0.01 mmfgraduation
0.001 in./graduation
0.1 mmtgraduation
0.01 in.igraduation
Table 5 2 Selection of Move Amount
in the STEP
Mode
\\
Metric
Inch
xl
=-4=-----
0.001 mmjstep 0.0001 in.jstep
-.
-----
x 10
0.01 mmlstep
0.001 in.lstep
x 100
0.1 mmlstep
0.01 in.istep
—..
x 103O
1.0 mmlstep 0.1 inlstep
+
x 10000
10.0 mmlstep
; 1.0 in.lstep
—------~ --
x ICOOOO
100.0 mmfstep ; 10.0 in.lstep
Z HANDLEt X HANDLE+
mm
~\J
For Z-ax,s
Far Xax, S
MANUAL
PULSE MULTIPLv
x 1O(I
x il)oo
4$)
x 10
xl .
x 10000
x
100 00(1
Parameter #6009 D4 can permit setting any
multiplication factor when MANUAL PULSE
MULTIPLY switch is set at X1OO. Multipli-
cation factor is set by parameter #6223.
Example:
When 50 is set for #6223, Xl, X1O,
x50, can be set.
5.1 .8.1 Handle Interpolation Function
5.1 .8.2 General
When the handle interpolation mode is commanded
while executing the program under memory mode,
tape mode, or MD I mode,
the handle can be turned
to the plus direction to control the cutting speed
of the GO1, G02, or G03 commands.
5.1 .8.3 Operation
(1) Select the handle interpolation mode.
The mode can be set by the setting parameter
or 1/0 input.
Setting #6001 D4:
1 = Enable handIe
interpolation mode
O = Disable handle
interpolation mode
1/0 signal #13066:
1 =
Enable handle
interpolation mode
O = Disable handle
interpolation mode
(2) Depress the cycle start button.
(3)
ItF!t blinks to
stop the machine before
executing the GO1 (or G02, G03) program.
(4) Turn the handle to the plus side, to perform
cutting interpolation for as long as the handle
is turned,
The F command is overridden in
proportion to the handle rotation speed.
The relation between the handle rotation
speed and the override is set in parameter
#6349.
(Example)
Jihen the relation between the rotation speed of
the handle and the override is “1 rotation/second =
100%”, the rate becomes as follows.
Parameter #6349 = 100 (pulses/second)
1 rotationlsecond or more
100%
0.5
rotations/second
’50%
0.01 rotations/second
1%
Less
than O.001 rotations/second
stop
(5)
The move stops when the ‘nandle is stopped
or when turned to the minus side.
(6) Turn off the handle interpolation mode when
the cutting ends.
Notes :
1.
The move has no disconnection if the handle
is turned faster than O.2 rotationlsecond, ‘out
the move is disconnected if the handle is
turned slower than O.2 rotationlsecond.
190