Need help?Do you have a question about the YASKAWA YASNAC J50 and is the answer not in the manual?
General| Brand | YASKAWA |
|---|---|
| Model | YASNAC J50 |
| Category | Controller |
| Language | English |
Shows the system configuration of YASNAC J50, including CNC unit, operator's panel, I/O, feed servo, spindle unit, and machine.
Details calculating heat exchanger capacity based on cabinet dimensions and heat transmission.
Lists heat values for NC Units and Servo Units, including total, internal, and regenerative values.
Shows the layout of connectors on the CNC unit JZNC-JRKOO, identifying PC50, CP50, SR50, and CN01-CN03.
Provides a connection diagram for the YASNAC J50L CNC unit in a lathe configuration, detailing connections to operator's panel and I/O modules.
Shows the power supply connection diagram for the CNC unit's CPS-18FB, indicating connector C03.
Details the power supply connection for the CPS unit, specifying single-phase 200/220/230VAC input.
Illustrates the connection between JANCD-PC50, CPS-18FB, and the CNC Operator's Panel (JANCD-SP50).
Shows the connection of a manual pulse generator to the CNC Operator's Panel (JANCD-SP50) via CN1.
Illustrates the connection of input sequence signals from the CNC unit (JANCD-PC50) to external units like brake, servo units, and tape reader.
Shows cable connections between the CNC unit and feed servo units for the 1st and 3rd axes (Lathe).
Details connections for spindle drive units with built-in PG for lathe and multi-axis lathe configurations.
Shows the connection between the CNC unit (JANCD-CP50) and the Tape Reader Unit (Model 2801) via CN20.
Details the connection to the tape reader, including power supply and transformer connections.
Illustrates the connection between the CNC unit (JANCD-CP50) and an RS-232C interface via CN20.
Shows the RS-232C interface connections to the outside of the NC unit, detailing the DB-25S/DB-25P connectors.
Shows the connection of direct-in signals to the CNC unit (JANCD-PC50) via CN10, specifying OV common.
Explains direct-in signal connection for OV common and +24V common, detailing I/O circuits.
Shows the connection of general-purpose I/O signals between the CNC unit (JANCD-PC50) and I/O modules (JANCD-FC810, FC860, FC861).
Details the connection of general-purpose I/O signals, showing the signal flow to I/O modules.
Illustrates connections for various I/O modules (FC810, FC860, FC861, SP50) to the CNC unit and operator's panel.
Lists various interface cables, their configurations, and remarks, including I/O, servo, spindle, and pulse generator connections.
Lists connectors for CNC units like CPS-18FB, JANCD series, and their cable side counterparts.
Lists connectors for CNC Operator's Panels (JANCD-SP50-1, -2) and their cable side configurations.
Lists connectors for I/O modules (JANCD-FC810, FC860, FC861) and their cable side configurations.
Lists connectors for Drive Units (SGDB-AD, CIMR-VM3) and their cable side configurations.
Lists standard input signals (PLC->NC) for YASNAC J50L, detailing codes like EDIT, MEMORY, TAPE, HANDLE, JOG, etc.
Explains input signals for cycle start, stop, and output signals for cycle start and feedhold, including timing charts.
Describes input and output signals for various control operation modes like JOG, H/S, T, MDI, MEM, EDT, AUT, MAN.
Lists standard input signals (PLC->NC) for YASNAC J50M, covering EDIT, MEMORY, TAPE, HANDLE, JOG, and RAPID TRAVERSE.
Explains input signals for cycle start, stop, and output signals for cycle start and feedhold, including timing charts.
Describes input and output signals for various control operation modes like JOG, H/S, T, MDI, MEM, EDT, AUT, MAN.
Provides dimensional drawings for the CNC Unit (Type JZNC-JRKOO), showing overall dimensions and mounting details.
Shows dimensional drawings for the Vertical CRT Operator's Panel (Type JZNC-JOPO1), including panel and cutout dimensions.
Provides dimensional drawings for the Horizontal CRT Operator's Panel (Type JZNC-JOP02), including panel and cutout dimensions.
Shows dimensional drawings for Servo Units (Types SGDB-05 to 15AD and SGDB-20 to 30AD), including mounting fittings.
Provides dimensional drawings for Noise Filters (Types LF310, LF320, LF330), including mounting details.
Shows dimensional drawings for Power Supply Units for Brake (Types LPDE-1HO1, LPSE-2H01).
Provides dimensional drawings for the Manual Pulse Generator (Type PREH-2E5T/100-M).
Shows dimensional drawings and specifications for Spindle Pulse Generators (Types PC-1024ZL, PC-1024ZL-4K, PC-1024ZL-160).
Shows I/O area numbers for rotary switch settings on SP 50, FC 861, FC 810/FC 860 modules.
Details address classifications for I/O modules SP 50, FC 861, FC 810, and FC 860.
Explains setting logic to '1' via SW2 for FC810, FC860, FC861 input contacts.
To Next Page