Why are the time and date wrong on my Yealink Conference System?
If the time and date are wrong on your Yealink Conference System, it may be because the system fails to obtain the time and date from the SNTP server automatically. Contact your network administrator. You can also manually configure the time and date.
What to do if I forget the administrator password for my Yealink VCM34?
If you forget the administrator password for your Yealink Conference System, and cannot access the advanced settings, you will need to reset your system.
Why can't the far site hear me on my Yealink VCM34?
If the far site cannot hear your audio during a call using the Yealink Conference System, ensure your audio input device is correctly connected and that the speaker at the far site isn't covered or damaged. Also, check if your microphone is muted and ask the far site to verify their volume isn't set to 0.
Why is the voice quality poor on my Yealink VCM34 Conference System?
If you are experiencing poor voice quality, such as intermittent voice, echo, or other noise, with your Yealink Conference System, try adjusting your distance from the microphone. Ensure the audio pickup device is stationary. Network congestion or old cables may also be factors; contact your network administrator or replace old cables.
Why is the audio unclear on my Yealink Conference System during a call?
If you cannot hear the audio clearly during a call on your Yealink Conference System, try adjusting the speaker volume. If the audio from the far site is muffled, they may be in a highly reverberant room—advise them to speak closer to their phone. Check your audio codec priority, enable noise suppression, and ensure the device is clean and free of dust.
Why can't I hear the ringtone on my Yealink VCM34?
If you cannot hear the ring tone when receiving a call on your Yealink Conference System, the volume might be set to 0. Try adjusting the volume.
Why is my Yealink VCM34 remote control not working?
If your Yealink Conference System isn't responding to the remote, the issue could be due to several reasons. First, the remote control battery might be dead, so try replacing the batteries. Second, the batteries might be installed incorrectly; ensure they are correctly installed. Finally, make sure you are aiming the remote control directly at the sensor on the device when performing a task.
Why is there no picture on the monitor for my Yealink Conference System?
If there is no picture on the monitor connected to your Yealink Conference System, the system may be in sleep mode. Press any key on the remote control to wake up the system. Alternatively, the system may be powered off, so ensure that the system is powered on. Also, check that the HDMI cable is correctly connected to the system, according to the Quick Start Guide.
Why can't I hear the ring tone on my Yealink VCM34?
If you cannot hear the ring tone when receiving a call on your Yealink Conference System, adjust the volume.
Why can't I share content on my Yealink VCM34?
If you cannot share content from your Yealink Conference System, ensure your PC is properly connected and turned on. If you're using a VCH50/VCH51 video conferencing hub or WPP20 wireless presentation pod, try replacing it. If using a WPP20, ensure it's connected to the video conferencing system to obtain the Wi-Fi profile and that the wireless AP feature of the video conferencing system is enabled.
You can take Yealink microphone devices (VCM34/VCM38/CPW90) as the audio input devices for MeetingBar AX0.
Details prerequisites and important notes before connecting microphone devices.
Lists supported microphones and their maximum cascade numbers for A20 and A30.
Instructions for connecting the VCM34 microphone to the MeetingBar AX0 using a network cable.
Instructions for connecting the VCM38 microphone to the MeetingBar AX0 using a network cable.
Instructions for connecting and pairing the CPW90 wireless microphone with the MeetingBar AX0.
Configures the audio input device on the CTP18 interface by navigating system settings.
General| Product type | Microphone |
|---|---|
| Product color | Black, Grey |
| LED indicators | Yes |
| Package depth | 196 mm |
| Package width | 310 mm |
| Package height | 80 mm |
| Package weight | 4260 g |
| Connectivity technology | Wired |
| Ethernet LAN (RJ-45) ports | 2 |
| Power source type | PoE |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 5 - 90 % |
| Quantity | 1 |
| Cables included | LAN (RJ-45) |
Weight and Dimensions| Depth | 171.5 mm |
|---|---|
| Width | 169 mm |
| Height | 37.5 mm |
To Next Page
