What to do if my Zanussi ZDLN7531 Dishwasher doesn't fill with water?
If your Zanussi Dishwasher doesn't fill with water and the display shows i10 or i11, ensure that the water tap is open, the water supply pressure isn't too low (contact your local water authority for information), the water tap isn't clogged, the filter in the inlet hose isn't clogged, and the inlet hose has no kinks or bends.
What to do if my Zanussi Dishwasher doesn't drain the water?
If your Zanussi Dishwasher does not drain water and the display shows i20, make sure the sink spigot and the interior filter system are not clogged, and that the drain hose has no kinks or bends.
What to do if Zanussi Dishwasher programme does not start?
If the programme does not start on your Zanussi Dishwasher, ensure that the appliance door is closed. If the delay start is set, cancel the setting or wait for the end of the countdown. Also, the appliance may be recharging the resin inside the water softener, which takes approximately 5 minutes.
Why is my Zanussi Dishwasher leaking from the door?
If there's a small leak from the door of your Zanussi Dishwasher, the appliance may not be leveled. Loosen or tighten the adjustable feet (if applicable). Also, the appliance door may not be centered on the tub; adjust the rear foot if needed.
What to do if anti-flood device is on in my Zanussi Dishwasher?
If the anti-flood device is on and the display shows i30 on your Zanussi Dishwasher, close the water tap. Also, ensure the appliance is correctly installed and the baskets are loaded as instructed in the user manual.
Why does my Zanussi ZDLN7531 trip the circuit breaker?
If your Zanussi Dishwasher trips the circuit breaker, the amperage may be insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter, or turn off one of the appliances in use. It may also indicate an internal electrical fault, in which case you should contact an Authorised Service Centre.
Why is the Zanussi Dishwasher door difficult to close?
If the appliance door of your Zanussi Dishwasher is difficult to close, it might not be leveled. Try loosening or tightening the adjustable feet. Also, make sure that parts of the tableware are not protruding from the baskets.
Why is my Zanussi Dishwasher making rattling noises?
If you hear rattling or knocking sounds from inside your Zanussi Dishwasher, the tableware may not be properly arranged in the baskets. Refer to the basket loading leaflet. Also, make sure that the spray arms can rotate freely.
What to do if water level is too high in Zanussi Dishwasher?
If the level of water inside your Zanussi Dishwasher is too high and the display shows iF1, switch the appliance off and on. Also, make sure that the filters are clean and that the outlet hose is installed at the right height above the floor. Refer to the installation instructions.
Why is water temperature too high in Zanussi Dishwasher?
If the temperature of the water inside your Zanussi Dishwasher is too high, or if a malfunction of the temperature sensor occurred and the display shows i61 or i69, make sure that the temperature of the inlet water does not exceed 60°C. You can also try switching the appliance off and on.
General| Type | Freestanding |
|---|---|
| Energy Efficiency Class | A++ |
| Number of Place Settings | 13 |
| Noise Level | 44 dB |
| Height | 85 cm |
| Width | 60 cm |
| Drying Class | A |
| Delay Start | Yes |
| Half Load Option | Yes |
| Size | Full Size |
| Water Consumption per Cycle | 9.5 L |
To Next Page
