How to improve washing results in Zanussi Dishwasher?
To improve poor washing results with your Zanussi Dishwasher, refer to 'Daily use', 'Hints and tips' and the basket loading leaflet. Also, use a more intensive washing program, activate the Extra Power option, and clean the spray arm jets and filter.
Why Zanussi ZDLN7530 is not filling with water?
If your Zanussi Dishwasher is not filling with water and the display shows i10 or i11, make sure the water tap is open, the water supply pressure is adequate, the water tap and the filter in the inlet hose are not clogged, and the inlet hose has no kinks or bends. Contact your local water authority to check the pressure of the water supply.
How to fix a leaky Zanussi ZDLN7530 Dishwasher door?
To fix a small leak from the Zanussi Dishwasher door, ensure the appliance is level by adjusting the adjustable feet and that the door is centered on the tub by adjusting the rear foot.
What to do if the anti-flood device is on in Zanussi ZDLN7530 Dishwasher?
To prevent the anti-flood device from activating on your Zanussi Dishwasher and displaying 'i30', close the water tap, ensure the appliance is correctly installed, and load the baskets as instructed in the user manual.
How to improve drying results in Zanussi ZDLN7530?
If you experience poor drying results with your Zanussi Dishwasher, activate the AirDry function, ensure the rinse aid dispenser is filled to the correct level, use rinse aid even with multi-tablets, and consider that plastic items may need to be towel dried. Also, check if the selected program includes a drying phase. The quality of the rinse aid can also be the cause.
Why is there detergent left in Zanussi Dishwasher dispenser?
To address residues of detergent in the dispenser at the end of a Zanussi Dishwasher program, ensure the detergent tablet isn't stuck in the dispenser, that water can wash away the detergent by checking for blocked or clogged spray arms, and that items in the baskets do not prevent the detergent dispenser lid from opening.
Why is the interior of my Zanussi ZDLN7530 wet?
If you find the interior of your Zanussi Dishwasher is wet, this is normal. Humidity condenses on the appliance walls and is not a defect.
How to stop unusual foam during washing in Zanussi Dishwasher?
If you observe unusual foam during washing in your Zanussi Dishwasher, use a detergent specifically designed for dishwashers, try a detergent from a different manufacturer, and avoid pre-rinsing dishes under running water.
How to remove limescale from Zanussi Dishwasher?
If you notice limescale deposits on the tableware, tub, or inside the door of your Zanussi Dishwasher, check the salt level and refill if low, ensure the salt container cap is tight, and consider that your tap water may be hard. Use salt and set regeneration of the water softener, even when using multi-functional tablets. You can also start the Machine Care programme with a descaler designed for dishwashers. If deposits persist, try different detergents or contact the detergent manufacturer.
What to do if Zanussi Dishwasher displays i61 or i69?
If the temperature of the water inside your Zanussi Dishwasher is too high, or if a malfunction of the temperature sensor occurred and the display shows i61 or i69, ensure that the temperature of the inlet water does not exceed 60°C. You can also try switching the appliance off and on.
General| Type | Freestanding |
|---|---|
| Energy Efficiency Class | D |
| Number of Place Settings | 13 |
| Noise Level | 44 dB |
| Delay Start | Yes |
| Half Load Option | Yes |
| Drying System | AirDry |
| Plumbing | Cold or hot |
To Next Page
