What to do if water level is too high in Zanussi ZDLN1510?
If the level of water inside the Zanussi Dishwasher is too high, switch the appliance off and on. Also, make sure that the filters are clean and the outlet hose is installed at the right height above the floor. Refer to the installation instructions.
What to do if Zanussi Dishwasher does not drain water?
If your Zanussi Dishwasher isn't draining water, ensure the sink spigot and the interior filter system are not clogged. Also, check the drain hose for any kinks or bends.
How to fix a leaking Zanussi ZDLN1510 Dishwasher door?
If you notice a small leak from the door of your Zanussi Dishwasher, the appliance might not be level. Try adjusting the feet. Also, the door might not be centered on the tub, so adjust the rear foot if applicable.
What to do if Zanussi Dishwasher has wash pump malfunction?
If there is a malfunction of the wash pump or the drain pump in your Zanussi Dishwasher, switch the appliance off and on.
What to do if Zanussi Dishwasher water temperature is too high?
If the temperature of the water inside the Zanussi Dishwasher is too high or a malfunction of the temperature sensor occurred, make sure that the temperature of the inlet water does not exceed 60°C. Also, try switching the appliance off and on.
Why is the inside of my Zanussi Dishwasher wet?
If the interior of your Zanussi Dishwasher is wet, this is not a defect of the appliance; humidity condenses on the appliance walls.
Why Zanussi ZDLN1510 programme does not start?
If the programme on your Zanussi Dishwasher doesn't start, ensure the appliance door is fully closed. If the delay start is activated, either cancel the setting or wait for the countdown to finish. Also, the appliance may be recharging the resin inside the water softener, which takes about 5 minutes.
How to improve drying results in Zanussi ZDLN1510?
If you're experiencing poor drying results with your Zanussi Dishwasher, avoid leaving tableware inside the closed appliance for extended periods. Ensure the rinse aid dispenser is filled and the dosage is sufficient; adjust to a higher level if needed. Note that plastic items may require towel drying. For optimal drying, activate the AirDry function and always use rinse aid, even with multi-tablets.
What to do if Zanussi ZDLN1510 Dishwasher has water level detection sensor malfunction?
If you have a malfunction of the water level detection sensor in your Zanussi Dishwasher, make sure that the filters are clean and switch the appliance off and on.
Why does my Zanussi ZDLN1510 trip the circuit breaker?
If your Zanussi Dishwasher is tripping the circuit-breaker, it could be due to insufficient amperage. Check the socket amperage and the capacity of the meter, or turn off another appliance in use. If this doesn't resolve the issue, there may be an internal electrical fault.
General| Type | Freestanding |
|---|---|
| Appliance placement | Freestanding |
| Control panel colour | White |
| Noise Level | 49 dB |
| Number of Washing Programs | 5 |
| Delayed Start Timer | Yes |
| Delay Start (max) | 24 hours |
| Energy Efficiency Class | F |
| Energy Consumption per Cycle | 1.039 kWh |
| Annual Energy Consumption | 295 kWh |
| Drying Class | A |
| Half Load Option | No |
| Child Lock | No |
| Drying system | Residual heat |
| Product size | 60 cm |
| Number of Place Settings | 13 |
| Wash Programs | Eco, Intensive, Normal, Quick |
| Water Consumption per Cycle | 11 litres |
| Annual Water Consumption | 3080 L |
| Programs | Eco, Intensive, Normal, Quick |
To Next Page
